AD5560JBCZ datasheet(44/67 Pages) AD

44 / 67 page

Data Sheet

AD5560

Rev. E | Page 43 of 66

internal current range enabled and ~1 W with external current

ranges, EXTFORCE1 or EXTFORCE2, enabled. This device is

specified for performance up to 90°C junction temperature (TJ).

PACKAGE COMPOSITION AND MAXIMUM

VERTICAL FORCE

The exposed pad and leads of the TQFP package have a 100%

tin finish. The exposed paddle is connected internally to AVSS.

The simulated maximum allowable force for a single lead is

0.18 lbs; total allowable force for the package is 11.5 lbs. The

quoted maximum force may cause permanent lead bending.

Other package failure (die, mold, board) may occur first at

lower forces.

SLEW RATE CONTROL

There are two methods of achieving different slew rates using

the AD5560. One method is using the programmable slew rate

feature that gives eight programmable rates. The second

method is using the ramp feature and an external clock.

Programmable Slew Rate

Eight programmable modes of slew rates are available to choose

from through the serial interface, enabling the user to choose

different rates to power up the DUT. The different slew rates

are achieved by variation in the internal compensation of the

force DAC output amplifier. The slew rates available are

1.000 V/µs, 0.875 V/µs, 0.750 V/µs, 0.625 V/µs, 0.5 V/µs,

0.4375 V/µs, 0.35V µs, and 0.313 V/µs.

Ramp Function

Included in the AD5560 is a ramp function that enables the

user to apply a rising or falling voltage ramp to the DUT. The

user supplies a clock, RCLK, to control the timing.

This function is controlled via the serial interface and requires

programming of a number of registers to determine the end

value, the ramp size, and the clock divider register to determine

the update rate.

The contents of the FIN DAC x1 register are the ramp start

value. The user must load the end code register and the step

size register. The sign is now generated from the difference

between the FIN DAC x1 register and the end code; then the

step size value is added to or subtracted from FIN DAC x1,

calibrated and stored. The user must supply a clock to the RCLK

pin to load the new code to the DAC. The output settles in 1.2 µs

for a step of 10 mV with CDUT in the lowest range of <0.2 µF.

While the output is settling, the next step is calculated to be

ready for the next ramp clock. The calibration engine is used

here; therefore, there is a calibration delay of 1.2 µs.

The ramp timing is controlled in two ways: by a user-supplied

clock (RCLK) and by a clock divider register. This gives the

user much flexibility over the frequency of the ramp steps. The

ramp typically starts after (2 × clock divider + 2) clocks,

although there can be a ±1 clock delay due to the asynchronous

nature of RCLK. The external clock can be a maximum of 833

kHz when using clock divider = 1. Faster RCLK speeds can be

used, but the fastest ramp rate is linked into the DAC

calibration engine.

For slower ramp rates, an even slower RCLK can be used.

The step sizes are in multiples of 16 LSBs. If the code previous

to the end code is not a multiple of this step size, the last step is

smaller. If the ramp function must be interrupted at any stage

during the ramp, write the interrupt ramp command. The FIN

DAC x1 stops ramping at the current value and returns to

normal operation.

The fastest ramp rate is 0.775 V/µs (for a 5 V reference and an

833 kHz clock using a 2032 LSB step size and divider = 1).

The slowest ramp rate is 24 µV/µs (for a 5 V reference and an

833 kHz clock using a 16 LSB step size and divider = 255).

Even slower ramps can be achieved with slower SCLK. The

ramp continues until any of the following occurs:

•

It reaches the end code.

•

An interrupt ramp is received from the user.

•

If any enabled alarm triggers, the ramp stops to allow

the user to service the activated alarm.

While the device is in ramp mode, the only command that the

interface accepts is an interrupt ramp. No other commands should

be written to the device while ramping because they are ignored.

AD5560JBCZ Datasheet(PDF) 44 Page - Analog Devices

AD5560JBCZ Datasheet(HTML) 44 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67

Datasheet Download

Link URL