Electronic Components Datasheet Search
  English  ▼

X  

COP411C Datasheet(PDF) 9 Page - National Semiconductor (TI)

[Old version datasheet] Texas Instruments acquired National semiconductor.
Part # COP411C
Description  Single-Chip CMOS Microcontrollers
PDF  20 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  NSC [National Semiconductor (TI)]
Direct Link  http://www.national.com
Logo NSC - National Semiconductor (TI)

COP411C Datasheet(HTML) 9 Page - National Semiconductor (TI)

Back Button COP411C Datasheet HTML 5Page - National Semiconductor (TI) COP411C Datasheet HTML 6Page - National Semiconductor (TI) COP411C Datasheet HTML 7Page - National Semiconductor (TI) COP411C Datasheet HTML 8Page - National Semiconductor (TI) COP411C Datasheet HTML 9Page - National Semiconductor (TI) COP411C Datasheet HTML 10Page - National Semiconductor (TI) COP411C Datasheet HTML 11Page - National Semiconductor (TI) COP411C Datasheet HTML 12Page - National Semiconductor (TI) COP411C Datasheet HTML 13Page - National Semiconductor (TI) Next Button
Zoom Inzoom in Zoom Outzoom out
 9 / 20 page
background image
Functional Description (Continued)
HALT MODE
The COP410C411C is a
fully static circuit therefore the
user may stop the system oscillator at any time to halt the
chip The chip also may be halted by the HALT instruction or
by forcing CKO high when it is used as a HALT IO port
Once in the HALT mode the internal circuitry does not re-
ceive any clock signal and is therefore frozen in the exact
state it was in when halted All information is retained until
continuing The HALT mode is the minimum power dissipa-
tion state
The HALT mode has slight differences depending upon the
type of oscillator used
a 1-pin oscillatorRC or external
The HALT mode may be entered into by either program
control (HALT instruction) or by forcing CKO to a logic
‘‘1’’ state
The circuit may be awakened by one of two different
methods
1) Continue function By forcing CKO to a logic ‘‘0’’ the
system clock is re-enabled and the circuit continues to
operate from the point where it was stopped
2) Restart Forcing the RESET pin to a logic ‘‘0’’ will re-
start the chip regardless of HALT or CKO (see initiali-
zation)
b 2-pin oscillatorcrystal
The HALT mode may be entered into by program control
(HALT instruction) which forces CKO to a logic ‘‘1’’ state
The circuit can be awakened only by the RESET function
TLDD5015 – 7
Halt IO Port
CKO Pin Options
In a crystal-controlled oscillator system CKO is used as an
output to the crystal network CKO will be forced high during
the execution of a HALT instruction thus inhibiting the crys-
tal network If a 1-pin oscillator system is chosen (RC or
external) CKO will be selected as HALT and is an IO
flip-flop which is an indicator of the HALT status An exter-
nal signal can override this pin to start and stop the chip By
forcing a high level to CKO the chip will stop as soon as
CKI is high and the CKO output will go high to keep the chip
stopped By forcing a low level to CKO the chip will contin-
ue and CKO output will go low
All features associated with the CKO IO pin are available
with the 24-pin package only
OSCILLATOR OPTIONS
There are three options available that define the use of CKI
and CKO
a Crystal-Controlled Oscillator CKI and CKO are connect-
ed to an external crystal The instruction cycle time
equals the crystal frequency divided by 16 (optionally by 8
or 4)
b External Oscillator CKI is configured as LSTTL-compati-
ble input accepting an external clock signal The external
frequency is divided by 16 (optionally by 8 or 4) to give
the instruction cycle time CKO is the HALT IO port
c RC-Controlled Oscillator CKI is configured as a single pin
RC-controlled Schmitt trigger oscillator The instruction
cycle equals the oscillation frequency divided by 4 CKO
is the HALT IO port
The RC oscillator is not recommended in systems that re-
quire accurate timing or low current The RC oscillator
draws more current than an external oscillator (typically an
additional 100 mA at 5V) However when the part halts it
stops with CKI high and the halt current is at the minimum
TLDD5015 – 8
FIGURE 6 COP410C Oscillator
Crystal or Resonator
RC-Controlled
Oscillator
Crystal
Component Value
Cycle
Value
R1
R2
C1 pF
C2 pF
R
C
Time
VCC
32 kHz
220k
20M
30
5-36
15k
82 pF
4-9 ms
t
45V
455 kHz
5k
10M
80
40
30k
82 pF
8-16 ms
t
45V
2096 MHz
2k
1M
30
6-36
47k
100 pF
16-32 ms
24 to 45
40 MHz
1k
1M
30
6-36
Note 15k s R s 150k
50 pf s C s 150 pF
9



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com