S71GL064A datasheet(21/134 Pages) SPANSION

21 / 134 page

February 8, 2005 S71GL064A_00_A2

S71GL064A based MCPs

Advance

Informatio n

Device Bus Operations

This section describes the requirements and use of the device bus operations, which are ini-

tiated through the internal command register. The command register itself does not occupy

any addressable memory location. The register is a latch used to store the commands, along

with the address and data information needed to execute the command. The contents of the

function of the device. Table 1 lists the device bus operations, the inputs and control levels

they require, and the resulting output. The following subsections describe each of these op-

erations in further detail.

Table 1. Device Bus Operations

Legend: L = Logic Low = VIL, H = Logic High = VIH, VID = 11.5–12.5 V, VHH = 11.5–12.5 V, X = Don’t Care, SA = Sector

Address, AIN = Address In, DIN = Data In, DOUT = Data Out

Notes:

1. Addresses are Amax:A0 in word mode; Amax:A-1 in byte mode. Sector addresses are Amax:A15 in both modes.

2. The sector protect and sector unprotect functions may also be implemented via programming equipment. See the “Sector Group Protection

and Unprotection” section.

3. If WP# = VIL, the first or last sector remains protected (for uniform sector devices), and the two outer boot sectors are protected (for boot

sector devices). If WP# = VIH, the first or last sector, or the two outer boot sectors will be protected or unprotected as determined by the

method described in “Sector Group Protection and Unprotection”. All sectors are unprotected when shipped from the factory (The Secured

Silicon Sector may be factory protected depending on version ordered.)

4. DIN or DOUT as required by command sequence, data polling, or sector protect algorithm (see Figure 2).

Requirements for Reading Array Data

To read array data from the outputs, the system must drive the CE# and OE# pins to VIL.

CE# is the power control and selects the device. OE# is the output control and gates array

data to the output pins. WE# should remain at VIH.

The internal state machine is set for reading array data upon device power-up, or after a hard-

ware reset. This ensures that no spurious alteration of the memory content occurs during the

power transition. No command is necessary in this mode to obtain array data. Standard mi-

croprocessor read cycles that assert valid addresses on the device address inputs produce

Operation

CE#

OE#

WE# RESET#

WP#

ACC

Addresses

(Note 1)

DQ0–DQ15

Read

AIN

DOUT

Write (Program/Erase)

(Note 3)

AIN

(Note 4)

Accelerated Program

(Note 3) VHH

AIN

(Note 4)

Standby

VCC ±

0.3 V

VCC ±

0.3 V

High-Z

Output Disable

High-Z

Reset

High-Z

Sector Group Protect

(Note 2)

VID

SA, A6 =L,

A3=L, A2=L,

A1=H, A0=L

(Note 4)

Sector Group

Unprotect

(Note 2)

VID

SA, A6=H,

A3=L, A2=L,

A1=H, A0=L

(Note 4)

Temporary Sector

Group Unprotect

VID

AIN

(Note 4)

S71GL064A Datasheet(PDF) 21 Page - SPANSION

S71GL064A Datasheet(HTML) 21 Page - SPANSION

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL