Philips Semiconductors

Product data

XA-G30

XA 16-bit microcontroller family

512 B RAM, watchdog, 2 UARTs

2002 Mar 25

7

NAME

RESET

VALUE

BIT FUNCTIONS AND ADDRESSES

SFR

ADDRESS

DESCRIPTION

NAME

RESET

VALUE

LSB

MSB

SFR

ADDRESS

DESCRIPTION

357

356

355

354

353

352

351

350

SWR*

Software Interrupt Request

42A

—

SWR7

SWR6

SWR5

SWR4

SWR3

SWR2

SWR1

00

2C7

2C6

2C5

2C4

2C3

2C2

2C1

2C0

T2CON*

Timer 2 control register

418

TF2

EXF2

RCLK0

TCLK0

EXEN2

TR2

C/T2

CP/RL2

00

2CF

2CE

2CD

2CC

2CB

2CA

2C9

2C8

T2MOD*

Timer 2 mode control

419

—

—

RCLK1

TCLK1

—

—

T2OE

DCEN

00

TH2

Timer 2 high byte

459

00

TL2

Timer 2 low byte

458

00

T2CAPH

Timer 2 capture register,

high byte

45B

00

T2CAPL

Timer 2 capture register,

low byte

45A

00

287

286

285

284

283

282

281

280

TCON*

Timer 0 and 1 control register

410

TF1

TR1

TF0

TR0

IE1

IT1

IE0

IT0

00

TH0

Timer 0 high byte

451

00

TH1

Timer 1 high byte

453

00

TL0

Timer 0 low byte

450

00

TL1

Timer 1 low byte

452

00

TMOD

Timer 0 and 1 mode control

45C

GATE

C/T

M1

M0

GATE

C/T

M1

M0

00

28F

28E

28D

28C

28B

28A

289

288

TSTAT*

Timer 0 and 1 extended status

411

—

—

—

—

—

T1OE

—

T0OE

00

2FF

2FE

2FD

2FC

2FB

2FA

2F9

2F8

WDCON*

Watchdog control register

41F

PRE2

PRE1

PRE0

—

—

WDRUN

WDTOF

—

Note 6

WDL

Watchdog timer reload

45F

00

WFEED1

Watchdog feed 1

45D

x

WFEED2

Watchdog feed 2

45E

x

NOTES:

*

SFRs are bit addressable.

1. At reset, the BCR register is loaded with the binary value 0000 0a11, where “a” is the value on the BUSW pin. This defaults the address bus

size to 20 bits since the XA-G30 has only 20 address lines.

2. SFR is loaded from the reset vector.

3. All bits except F1, F0, and P are loaded from the reset vector. Those bits are all 0.

4. Unimplemented bits in SFRs are X (unknown) at all times. Ones should not be written to these bits since they may be used for other

purposes in future XA derivatives. The reset value shown for these bits is 0.

5. Port configurations default to quasi-bidirectional when the XA begins execution from internal code memory after reset, based on the

condition found on the EA pin. Thus all PnCFGA registers will contain FF and PnCFGB registers will contain 00. When the XA begins

execution using external code memory, the default configuration for pins that are associated with the external bus will be push-pull. The

PnCFGA and PnCFGB register contents will reflect this difference.

6. The WDCON reset value is E6 for a Watchdog reset, E4 for all other reset causes.

7. The XA-G30 implements an 8-bit SFR bus, as stated in Chapter 8 of the

XA User Guide. All SFR accesses must be 8-bit operations. Attempts

to write 16 bits to an SFR will actually write only the lower 8 bits. Sixteen bit SFR reads will return undefined data in the upper byte.