Electronic Components Datasheet Search
  English  ▼

X  

ACT2823 Datasheet(PDF) 18 Page - Active-Semi, Inc

Part # ACT2823
Description  Dual Cell Li-Ion Battery Charger and Power Bank Manager
PDF  25 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  ACTIVE-SEMI [Active-Semi, Inc]
Direct Link  http://www.active-semi.com
Logo ACTIVE-SEMI - Active-Semi, Inc

ACT2823 Datasheet(HTML) 18 Page - Active-Semi, Inc

Back Button ACT2823 Datasheet HTML 14Page - Active-Semi, Inc ACT2823 Datasheet HTML 15Page - Active-Semi, Inc ACT2823 Datasheet HTML 16Page - Active-Semi, Inc ACT2823 Datasheet HTML 17Page - Active-Semi, Inc ACT2823 Datasheet HTML 18Page - Active-Semi, Inc ACT2823 Datasheet HTML 19Page - Active-Semi, Inc ACT2823 Datasheet HTML 20Page - Active-Semi, Inc ACT2823 Datasheet HTML 21Page - Active-Semi, Inc ACT2823 Datasheet HTML 22Page - Active-Semi, Inc Next Button
Zoom Inzoom in Zoom Outzoom out
 18 / 25 page
background image
ACT2823
REV 1, 01-DEC-2016
Innovative PowerTM
ActiveSwitcherTM
is a trademark of Active-Semi.
18
∗
∗ 1
∗
14
Where IOUT is the load current, VOUT is the 5V output
voltage, VBAT is the battery voltage, FSW is the switching
frequency, and VRIPPLE is the desired ripple voltage.
Charge Current Sense Resistor
Choose a charge current sense resistor so the fast
charge current through it results in a current sense
voltage between 20mV-75mV. Typical resistor values
are 25mΩ to 50mΩ. The traces to the BATP and BATS
pins must be Kelvin sensed to ensure accuracy. In
noisy environments placing a 100nF capacitor between
BATP and BATS will improve noise immunity.
Output Sense Resistor
Choose an output current sense resistor so the
maximum load current through it results in a current
sense voltage greater than 10mV. The traces to the
CSP and CSN pins must be Kelvin sensed to ensure
accuracy.
The following equation sets the output
current limit
IOUT_CL
0.066
15
Where RCS is the current sense resistor between CSN
and CSP.
PCB Board Layout Guidance
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of
the IC.
1. Place the BAT decoupling capacitors as close to the
Bat pin as possible. Minimize the loop area between
the BAT pin to the capacitors to the PGND pin. If using
different sized capacitors, place the physically smaller
capacitors closer to the IC to get better high frequency
filtering.
2. Arrange the power components to reduce the overall
AC loop area.
3. Place the VOUT decoupling ceramic capacitors close
to the VOUT pin. Connect the ground side to the PGND
plane.
4. Place the VIN decoupling ceramic capacitors close to
the VIN pin. Connect the ground side to the PGND
plane.
5. Use Kevin sense connections from the output current
sense resistor to CSP and CSN pins, and from the
battery charging current sense resistor to BATS and
BATP.
6. SW node is noisy and should be isolated from other
sensitive circuitry. Make the connection from SW to the
inductor with a short, wide trace for good EMI and low
noise operation.
7. The exposed pad is must be connected to the top
layer GND plane. Connect it to the internal and bottom
layer ground planes using thermal vias. PGND and
AGND should be single-point connected to the exposed
pad under the IC.
8. An RC snubber and external Schottky diode across
SW to PGND can be added as needed for reducing
switching spikes and better EMI performance.
Application Circuit
The following schematic represents a typical application circuit.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com