| Electronic Components Datasheet Search |
|
LT3042 Datasheet(PDF) 16 Page - Linear Technology |
|
|
|||||||||||||||||||||||||||||
LT3042 Datasheet(HTML) 16 Page - Linear Technology |
|
16 / 22 page ![]() LT3095 16 3095fa For more information www.linear.com/LT3095 APPLICATIONS INFORMATION High Frequency Edges & Passive Filtering Techniques Figure 4 shows the output of the LT3095 boost converter in a typical application with a 50mA load, before and after filteringbythelinearregulator.Themostnoticeableresidual switching feature is the short spike when the boost power switch turns off. This edge is generated by high dI/dt cir- culating through the boost output capacitor parasitic and the corresponding magnetic circuit on the PCB. These edges can couple onto the output of the linear regulator indirectly through parasitic capacitance in the linear regulator or electromagnetically from one PCB trace to another. The spikes contain high frequency (>1MHz) content that the linear regulator control loop cannot ac- tively filter out. Minimize the residual spike amplitude by following the PCB layout guidelines provided in the next section. In many applications, the energy associated with the residual spikes is at a sufficiently high frequency that it does not interfere with the load. data0 data1 VIN = 5V VOUT = 15V ILOAD = 50mA fOSC = 1MHz 20MHz BW 1µs/DIV VBSTOUT 20mV/DIV VOUT 50µV/DIV 3095 F04 Figure 4. Output Transient Showing Spikes In cases where extreme ripple rejection up to very high frequencies is required, a passive filter at the output of the LDO can be used. Form a pi-network by placing the output capacitor very close to the LT3095 and another capacitor directly at the load, as shown Figure 5. Make sure the additional capacitor is large enough to present low impedance to the load across the full frequency range. PCB trace inductance between the LT3095 and load will provide some high-frequency filtering, but passives with additional impedance can offer further improvement. One option is a small resistor — typically an Ohm or less to avoidintroducingalargeloadregulationtermtothevoltage seen at the load. Another option is a low-ESR chip ferrite- bead or inductor. This solution offers the best rejection at very high frequencies (>10 MHz); however, a resonance is formed at a frequency of 1/ 2π LFILTERCLOAD ( ) that can amplify noise and introduce a new ripple component at the load. The peaking, or Q, associated with the filter can be reduced by introducing a series damping resistor or reducing the ratio LFILTER/CLOAD. COUT 2.2µF 0.1 CLOAD 1µF GND OUT1 LT3095 LOAD 3095 F05 Figure 5. Pi Network Filter Figure 6 shows the residual noise at the output of the LDO after it has been filtered with a 0.1Ω resistor and an additional 1µF capacitor at the load. The high frequency switch edges have been substantially reduced. data0 data0 VIN = 5V VOUT = 15V ILOAD = 50mA fOSC = 1MHz 20MHz BW 1µs/DIV VBSTOUT 20mV/DIV VOUT 50µV/DIV 3095 F06 Figure 6. Residual Ripple with Passive Pi Filter |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |