HIP6301VCB datasheet(5/20 Pages) RENESAS

5 / 20 page

HIP6301V, HIP6302V

FN9034 Rev 3.00

Page 5 of 20

May 5, 2008

VID4, VID3, VID2, VID1 and VID0

(Pins 1 thru 5 - Both Parts)

Voltage Identification inputs. The HIP6301V and HIP6302V

decode the VID bits to establish the reference voltage (see

Table 1). Each pin has an internal 20µA pull-up current source

to 2.5V making the parts compatible with CMOS and TTL

logic from 5V down to 2.5V. When a VID change is detected,

the reference voltage slowly ramps up or down to the new

value in 25mV steps. VID input levels above 2.9V may

produce an reference-voltage offset inaccuracy.

COMP (Pin 6 - Both Parts)

Output of the internal error amplifier. Connect this pin to the

external feedback and compensation network.

FB (Pin 7 - Both Parts)

Inverting input of the internal error amplifier.

FS/DIS (Pin 8 - Both Parts)

Channel frequency, FSW, select and disable. A resistor from

this pin to ground sets the switching frequency of the

converter. Pulling this pin to ground disables the converter

and three states the PWM outputs. See Figure 10.

GND (Pin 9 - Both Parts)

Bias and reference ground. All signals are referenced to this

pin.

VSEN (Pin 10 - Both Parts)

Power-good monitor input. Connect to the microprocessor CORE

voltage.

PWM1 (Pin 15 - HIP6301V, Pin 13 - HIP6302V),

PWM2 (Pin 14 - HIP6301V, Pin 12 - HIP6302V),

PWM3 (Pin 11 - HIP6301V only) and PWM4

(Pin 18 - HIP6301V only)

PWM outputs for each channel. Connect these pins to the

PWM input of the external MOSFET driver. For HIP6301V

systems using 3 channels, connect PWM4 high. For two

channel systems, connect PWM3 and PWM4 high.

ISEN1 (Pin 16 - HIP6301V, Pin 14 - HIP6302V),

ISEN2 (Pin 13 - HIP6301V, Pin 11 - HIP6302V),

ISEN3 (Pin 12 - HIP6301V only) and ISEN4

(Pin 17 - HIP6301V only)

Current sense inputs from the individual converter channel’s

phase nodes. Unused sense lines MUST be left open.

PGOOD (Pin 19 - HIP6301V, Pin 15 - HIP6302V)

Power-good. This pin is an open-drain logic signal that

indicates when the microprocessor CORE voltage (VSEN

pin) is within specified limits and soft-start has timed out.

VCC (Pin 20 - HIP6301V, Pin 16 - HIP6302V)

Bias supply. Connect this pin to a 5V supply.

HIP6301V and HIP6302V Functional Pin Descriptions

HIP6301V

(20 LD SOIC

TOP VIEW

HIP6302V

(16 LD SOIC

TOP VIEW

VID4

VID3

VID2

VID1

VID0

FS/DIS

PWM2

PGOOD

PWM3

ISEN4

ISEN1

VCC

GND

ISEN3

PWM4

VSEN

COMP

PWM1

ISEN2

VID4

VID3

VID2

VID1

VID0

FS/DIS

VSEN

PGOOD

PWM2

VCC

COMP

ISEN2

GND

ISEN1

PWM1

HIP6301VCB Datasheet(PDF) 5 Page - Renesas Technology Corp

HIP6301VCB Datasheet(HTML) 5 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Datasheet Download

Link URL