DirectDrive Video Amplifier with

Reconstruction Filter

Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are

implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.

Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 13

© 2005 Maxim Integrated Products

Printed USA

is a registered trademark of Maxim Integrated Products, Inc.

Package Information (continued)

(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,

go to www.maxim-ic.com/packages.)

0.10 C

0.08 C

0.10 M C A B

D

D/2

E/2

E

A1

A2

A

E2

E2/2

L

k

e

(ND - 1) X e

(NE - 1) X e

D2

D2/2

b

L

e

L

C

L

e

CL

L

C

L

C

E

1

2

21-0136

PACKAGE OUTLINE

12, 16L, THIN QFN, 3x3x0.8mm

1. DIMENSIONING & TOLERANCING CONFORM TO ASME Y14.5M-1994.

EXPOSED PAD VARIATIONS

1.10

T1633-1

0.95

CODES

PKG.

T1233-1

MIN.

0.95

NOM.

1.10

D2

1.25

1.10

0.95

1.25

NOM.

1.10

MAX.

1.25

MIN.

0.95

MAX.

1.25

E2

12

N

k

A2

0.25

NE

A1

ND

0

0.20 REF

-

-

3

0.02

3

0.05

L

e

E

0.45

2.90

b

D

A

0.20

2.90

0.70

0.50 BSC.

0.55

3.00

0.65

3.10

0.25

3.00

0.75

0.30

3.10

0.80

16

0.20 REF

0.25

-

0

4

0.02

4

-

0.05

0.50 BSC.

0.30

2.90

0.40

3.00

0.20

2.90

0.70

0.25

3.00

0.75

3.10

0.50

0.80

3.10

0.30

PKG

REF.

MIN.

12L 3x3

NOM.

MAX.

NOM.

16L 3x3

MIN.

MAX.

0.35 x 45∞

PIN ID

JEDEC

WEED-1

0.35 x 45∞

WEED-2

2. ALL DIMENSIONS ARE IN MILLIMETERS. ANGLES ARE IN DEGREES.

3. N IS THE TOTAL NUMBER OF TERMINALS.

4. THE TERMINAL #1 IDENTIFIER AND TERMINAL NUMBERING CONVENTION SHALL CONFORM TO

JESD 95-1 SPP-012. DETAILS OF TERMINAL #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED

WITHIN THE ZONE INDICATED. THE TERMINAL #1 IDENTIFIER MAY BE EITHER A MOLD OR

MARKED FEATURE.

5. DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.20 mm AND 0.25 mm

FROM TERMINAL TIP.

6. ND AND NE REFER TO THE NUMBER OF TERMINALS ON EACH D AND E SIDE RESPECTIVELY.

7. DEPOPULATION IS POSSIBLE IN A SYMMETRICAL FASHION.

8. COPLANARITY APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS.

9. DRAWING CONFORMS TO JEDEC MO220 REVISION C.

NOTES:

E

2

2

21-0136

PACKAGE OUTLINE

12, 16L, THIN QFN, 3x3x0.8mm

T1233-3

1.10

1.25

0.95

1.10

0.35 x 45∞

1.25

WEED-1

0.95

T1633F-3

0.65

T1633-4

0.95

0.80

0.95

0.65

0.80

1.10

1.25

0.95

1.10

0.225 x 45∞

0.95

WEED-2

0.35 x 45∞

1.25

WEED-2

T1633-2

0.95

1.10

1.25

0.95

1.10

0.35 x 45∞

1.25

WEED-2

NO

DOWN

BONDS

ALLOWED

YES

NO

YES

N/A

NO