Tolerance x.xx =

Pin 1 is marked by a “dot” or indentation on the side of the unit

For 5V, 12V & 24V input models, “W” = 0.24 in (6.0 mm)

For 48V input models, “W” = 0.28 in (7.2 mm)

Notes:

1. Output load regulation is specified for a load change of 20% to 100%.

2. When measuring output ripple, it is recommended that an external

ceramic capacitor (approx 10 µF) be placed across the output.

3. The 5V, 12V and 24V input units do not require external components

to operate, but the use of an input capacitor (10 µF) may enhance

performance in some applications. An output capacitor (1.0 µF to 10

µF) may be used to reduce ripple. The 48V input models require an

input capacitor of 4.7 uF to 47 uF (dependent upon the application).

4. It is recommended that a fuse be used on the input of a power supply

for protection. See the table above for the correct rating.

Derating Curve

-40

-10

0

5

15

25

35

45

55

65

75

85

95

105

0

20

40

60

80

100

Ambient Temperature

1C

0.02

(0.50)

0.01

(0.25)

0.77 (19.5)

7

6

12

0.08

(2.13)

0.10

(2.54)

0.37

(9.5)

0.12

(3.05)

0.05

(1.25)

Bottom

Side

“W”

0.20

(5.08)

0.02

(0.50)

45

0.02

(0.50)

MicroPower Direct

www.micropowerdirect.com

232 Tosca Drive Stoughton, MA 02072

■

TEL: (781) 344-8226

■

FAX: (781) 344-8481

■

E-Mail: sales@micropowerdirect.com

Model Selection Guide

Mechanical Dimensions

Pin Connections

Model

Number

Input

Output 1

Output 2

Efficiency

(%, Typ)

Fuse Rating

Slow-Blow

(mA)

Voltage (VDC)

Current (mA)

Voltage

(VDC)

Current

(mA, Max)

Current

(mA, Min)

Voltage

(VDC)

Current

(mA, Max)

Current

(mA, Min)

Nominal

Range

Full-Load No-Load

D101D

5

4.5 - 5.5

277

30

5.0

100.0

10.0

5.0

100.0

10.0

72

500

D102D

5

4.5 - 5.5

266

30

5.0

100.0

10.0

3.3

100.0

10.0

71

500

D103D

5

4.5 - 5.5

260

30

5.0

100.0

10.0

12.0

42.0

4.2

77

500

D104D

5

4.5 - 5.5

250

30

12.0

42.0

4.2

12.0

42.0

4.2

80

500

D105D

5

4.5 - 5.5

244

30

5.0

100.0

10.0

15.0

33.0

3.3

82

500

D106D

5

4.5 - 5.5

256

30

15.0

33.0

3.3

15.0

33.0

3.3

78

500

D111D

12

10.8 - 13.2

116

12

5.0

100.0

10.0

5.0

100.0

10.0

72

200

D112D

12

10.8 - 13.2

117

12

5.0

100.0

10.0

3.3

100.0

10.0

71

200

D113D

12

10.8 - 13.2

108

12

5.0

100.0

10.0

12.0

42.0

4.2

77

200

D114D

12

10.8 - 13.2

104

12

12.0

42.0

4.2

12.0

42.0

4.2

80

200

D115D

12

10.8 - 13.2

108

12

5.0

100.0

10.0

15.0

33.0

3.3

77

200

D116D

12

10.8 - 13.2

107

12

15.0

33.0

3.3

15.0

33.0

3.3

78

200

D121D

24

21.6 - 26.4

58

7

5.0

100.0

10.0

5.0

100.0

10.0

72

100

D122D

24

21.6 - 26.4

59

7

5.0

100.0

10.0

3.3

100.0

10.0

71

100

D123D

24

21.6 - 26.4

54

7

5.0

100.0

10.0

12.0

42.0

4.2

77

100

D124D

24

21.6 - 26.4

52

7

12.0

42.0

4.2

12.0

42.0

4.2

80

100

D125D

24

21.6 - 26.4

54

7

5.0

100.0

10.0

15.0

33.0

3.3

77

100

D126D

24

21.6 - 26.4

53

7

15.0

33.0

3.3

15.0

33.0

3.3

78

100

D131D

48

43.2 - 52.8

29

6

5.0

100.0

10.0

5.0

100.0

10.0

72

100

D132D

48

43.2 - 52.8

30

6

5.0

100.0

10.0

3.3

100.0

10.0

71

100

D133D

48

43.2 - 52.8

27

6

5.0

100.0

10.0

12.0

42.0

4.2

77

100

D134D

48

43.2 - 52.8

26

6

12.0

42.0

4.2

12.0

42.0

4.2

80

100

D135D

48

43.2 - 52.8

26

6

5.0

100.0

10.0

15.0

33.0

3.3

82

100

D136D

48

43.2 - 52.8

27

6

15.0

33.0

3.3

15.0

33.0

3.3

78

100

Pin

Function

1+Vin

2-Vin

4

+Vout 1

5

-Vout 1

6

+Vout 2

7

-Vout 2

Output 1

μF Max

Output 2

μF Max

100

100

Capacitive Load

T

1

+V

IN

-V

IN

Input Filter

&

Switching

Transistors

Output

Rectifier

&

Filter

Output

Rectifier

&

Filter

Block Diagram