Electronic Components Datasheet Search
  English  ▼

X  

FR9872 Datasheet(PDF) 10 Page - Fitipower Integrated Technology Inc.

Part # FR9872
Description  18V, 2.5A, 1.4MHz Synchronous Step-Down DC/DC Converter
PDF  13 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  FITIPOWER [Fitipower Integrated Technology Inc.]
Direct Link  http://www.fitipower.com/en_US/index.asp
Logo FITIPOWER - Fitipower Integrated Technology Inc.

FR9872 Datasheet(HTML) 10 Page - Fitipower Integrated Technology Inc.

Back Button FR9872 Datasheet HTML 5Page - Fitipower Integrated Technology Inc. FR9872 Datasheet HTML 6Page - Fitipower Integrated Technology Inc. FR9872 Datasheet HTML 7Page - Fitipower Integrated Technology Inc. FR9872 Datasheet HTML 8Page - Fitipower Integrated Technology Inc. FR9872 Datasheet HTML 9Page - Fitipower Integrated Technology Inc. FR9872 Datasheet HTML 10Page - Fitipower Integrated Technology Inc. FR9872 Datasheet HTML 11Page - Fitipower Integrated Technology Inc. FR9872 Datasheet HTML 12Page - Fitipower Integrated Technology Inc. FR9872 Datasheet HTML 13Page - Fitipower Integrated Technology Inc.  
Zoom Inzoom in Zoom Outzoom out
 10 / 13 page
background image
10
FR9872-1.3-MAR-2012
FR9872
85T
fitipower integrated technology lnc.
Application Information
Output Voltage Setting
The output voltage VOUT is set by using a resistive
divider from the output to FB.
The FB pin regulated
voltage is 0.925V.
Thus the output voltage is:
VOUT=0. 2
1
R1
R2
V
R2 recommended value is 10kΩ, so R1 is determined
by:
R1=10. 1 VOUT 0. 2 kΩ
Table 1 lists recommended values of R1 and R2 for
most used output voltage.
Table 1
Recommended Resistance Values
VOUT
R1
R2
12V
121
kΩ
10
kΩ
5V
44.2kΩ
10kΩ
3.3V
26.1
kΩ
10kΩ
2.5V
16.9
kΩ
10kΩ
1.8V
9.53
kΩ
10kΩ
Place resistors R1 and R2 close to FB pin to prevent
stray pickup.
Input Capacitor Selection
The use of the input capacitor is controlling the input
voltage ripple and the MOSFETS switching spike
voltage.
Because the input current to the step-down
converter is discontinuous, the input capacitor is
required to supply the current to the converter to keep
the DC input voltage.
The capacitor voltage rating
should be 1.25 to 1.5 times greater than the maximum
input voltage.
The input capacitor ripple current RMS
value is calculated as:
IIN(RMS =IOUT
D 1 D
Where D is the duty cycle of the power MOSFET.
A low ESR capacitor is required to keep the noise
minimum.
Ceramic
capacitors
are
better,
but
tantalum or low ESR electrolytic capacitors may also
suffice.
When
using
tantalum
or
electrolytic
capacitors, a 0.1
μF ceramic capacitor should be
placed as close to the IC as possible.
FR9872
C6
100μF/25V
EC x1
VIN
VIN
12V
C1
10μF/25V
MLCC x1
It is recommended that the input EC capacitor
could be added for applications if the FR9872
suffers high spike input voltage (ex. hot plug test).
It can eliminate the spike voltage induced the IC
damaged from high input voltage stress (see
Note1).
Table 2 lists recommended values of C1 and C6
for most used input voltage.
Table 2
Recommended Capacitor Values
VIN
C1
C6
5V
10
μF × 2
---
12V
10
μF × 1
100
μF × 1
18V
10
μF × 1
330
μF × 1
Output Capacitor Selection
The output capacitor is used to keep the DC output
voltage and supply the load transient current.
Low ESR capacitors are preferred.
Ceramic,
tantalum or low ESR electrolytic capacitors can be
used depending on the output ripple requirements.
Add a 100
μF or 470μF Low ESR electrolytic
capacitor when operating in high input voltage
range (VIN > 20V).
It can improve the device’s
stability.
The output ripple voltage ΔV
OUT
is
described as:
I=
VOUT
FOSC L
1
VOUT
VIN
VOUT= I
R SR
1
FOSC COUT
Where ΔI is the peak-to-peak inductor ripple
current, FOSC is the switching frequency, L is the
inductance value, VIN is the input voltage, VOUT is
the output voltage, RESR is the equivalent series
resistance value of the output capacitor, and the
COUT is the output capacitor.
When using the
ceramic capacitors, the RESR can be ignored and
the output ripple voltage ΔV
OUT is shown as:
VOUT=
I
FOSC COUT
When using tantalum or electrolytic capacitors,
typically 90% of the output voltage ripple is
contributed by the ESR of output capacitors.
The
output ripple voltage ΔV
OUT can be estimated as:
VOUT= I R SR



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com