| Electronic Components Datasheet Search |
|
SVRTR2805SFEM Datasheet(PDF) 9 Page - VPT, Inc. |
|
|
|||||||||||||||||||||||||||||
SVRTR2805SFEM Datasheet(HTML) 9 Page - VPT, Inc. |
|
9 / 15 page ![]() Sales Information Phone:(425) 353-3010 Fax: (425) 353-4030 SVRTR2800S - 8.0 E-mail: vptsales@vptpower.com Web: www.vptpower.com Page 9 SVRTR2800S Series 6.2.2 Adjusting the Output Voltage (+S) The output voltage set point of the converter can be adjusted using the +S pin. To adjust the output up, connect the trim resistor from +S to OUTCOM. The maximum trim range is +10% from nominal. The appropriate resistor values versus the output voltage are given in the table below. Because the +S pin can be sensitive to external noise, the trim resistor should be located close to the SVRTR converter with short interconnects. When adjusting the output voltage, do not exceed the rated total output power or output current. The –S pin should be connected to the OUTCOM pin. SVRTR283R3S SVRTR2805S SVRTR2812S SVRTR2815S +Vout (V) Rtrim (Ω) + Vout (V) Rtrim (Ω) + Vout (V) Rtrim (Ω) + Vout (V) Rtrim (Ω) 3.60 1.13k 5.50 1.05k 13.2 1.09k 16.50 1.09k 3.55 1.36k 5.45 1.18k 13.1 1.19k 16.40 1.18k 3.50 1.72k 5.40 1.33k 13.0 1.33k 16.30 1.28k 3.45 2.32k 5.35 1.54k 12.9 1.49k 16.20 1.4k 3.40 3.59k 5.30 1.82k 12.8 1.7k 16.10 1.54k 3.35 7.87k 5.25 2.22k 12.7 1.98k 16.00 1.71k 3.30 5.20 2.86k 12.6 2.38k 15.90 1.94k 5.15 4k 12.5 2.96k 15.80 2.22k 5.10 6.67k 12.4 3.94k 15.70 2.61k 5.05 20k 12.3 5.86k 15.60 3.16k 5.00 12.2 11.4k 15.50 4k 12.1 242k 15.40 5.46k 12.0 15.30 8.57k 15.20 20k 15.10 Note 1 15.00 1. Connect Rtrim = 400Ω from +VOUT (PIN 5) to +S (PIN 6) 6.2.3 Remote Sense (+S, -S) Remote sensing compensates for voltage drops in the output pins and traces by sensing and regulating directly at the load. The remote sense function can compensate for up to a 10% voltage drop (5% in the positive lead and 5% in the negative lead). The sum of the TRIM up and remote sense compensation cannot exceed 10% such that the voltage at the output terminals of the converter does not exceed 110% of the nominal output voltage. If not used, the user should connect +S to +VOUT and –S to OUTCOM at the pins of the converter. 6.2.4 Frequency Synchronization (SYNC) The SVRTR2800S Series will free run at a switching frequency of approximately 525 kHz, which has been set for optimum converter performance. Frequency synchronization is not necessary unless required by system constraints. The SVRTR2800S Series provides a frequency synchronization input (SYNC) referenced to INCOM. The SYNC pin can be driven by an external clock. The internal clock and internal power train will operate at the frequency applied to the SYNC pin. The SYNC pin should be driven with a TTL type 5 V square wave signal. The duty cycle of the square wave should be between 20% and 80%. The SYNC pin is internally capacitively-coupled and the internal load is equivalent to 220 pF. Proper layout and circuit techniques are necessary to prevent noise from being injected into this pin. Synchronized converters should be located physically close together and share a low impedance INCOM connection. The SYNC pin can be left open or connected to INCOM if not used. + - + - 2.5V Ri 100 10K 100 +VOUT 5 +S 6 -S 3 OUTCOM 4 Rtrim |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |