Electronic Components Datasheet Search
  English  ▼

X  

SM312W Datasheet(PDF) 4 Page - Banner Engineering Corp.

Part # SM312W
Description  DC Voltage Series
PDF  10 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  BANNER [Banner Engineering Corp.]
Direct Link  https://www.bannerengineering.com/us/en.html
Logo BANNER - Banner Engineering Corp.

SM312W Datasheet(HTML) 4 Page - Banner Engineering Corp.

  SM312W Datasheet HTML 1Page - Banner Engineering Corp. SM312W Datasheet HTML 2Page - Banner Engineering Corp. SM312W Datasheet HTML 3Page - Banner Engineering Corp. SM312W Datasheet HTML 4Page - Banner Engineering Corp. SM312W Datasheet HTML 5Page - Banner Engineering Corp. SM312W Datasheet HTML 6Page - Banner Engineering Corp. SM312W Datasheet HTML 7Page - Banner Engineering Corp. SM312W Datasheet HTML 8Page - Banner Engineering Corp. SM312W Datasheet HTML 9Page - Banner Engineering Corp. Next Button
Zoom Inzoom in Zoom Outzoom out
 4 / 10 page
background image
Retroreflective Mode Alignment
Retro
Target
A highly reflective object may reflect enough light back to a
retroreflective sensor to allow that object to slip through the
beam, without being detected. This problem is called “proxing,”
and the following methods may be used to correct it:
•
Position the sensor and retro target so the beam will
not strike a shiny surface perpendicular to the sensor
lens
•
Reduce the Gain adjustment
•
Add a polarizing filter (for model SM312LV)
Note:
•
Light condition: sensor output is
ON when there is no object in the
beam
•
Dark condition: sensor output is ON
when there is an object in the beam
Convergent Mode Alignment
Object
Low
Reflectivity
Background
The sensing energy of a convergent mode sensor is
concentrated at the specified focus point. Convergent mode
sensors are less sensitive to background reflections, compared
with diffuse mode sensors. However, if background reflections
are a problem:
•
Skew the sensor position at a 10° to 25° angle to
eliminate direct reflections from shiny background
surfaces
•
Reduce the reflectivity of the background by painting
the surface(s) flat-black, scuffing any shiny surface, or
drilling a large hole, directly opposite the sensor
•
Reduce the Gain adjustment
Note:
•
Light condition: sensor output is
ON when there is no object in the
beam
•
Dark condition: sensor output is ON
when there is an object in the beam
Plastic Fiber Installation
Trimmed fiber
control ends
Plastic fiber
emitter port
Plastic fiber
receiver port
Gripper
Unlock
Lock
Adapters for
0.25- and 0.5-mm fibers
Sensor Face
1. With supplied fiber cutter, make a clean cut at the control
ends of fibers.
2. Unlock the fiber gripper as shown in the drawing.
3. Apply appropriate fiber adaptors to the fiber, if needed.
4. Gently insert the prepared fiber ends into the ports as far as
they will go.
5. Slide the fiber gripper back to lock, as shown in the drawing.
MINI-BEAM® DC Voltage Series
4
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 69943 Rev. F



Html Pages

1 2 3 4 5 6 7 8 9 10


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com