Electronic Components Datasheet Search
  English  ▼

X  

LXS6 Datasheet(PDF) 1 Page - Banner Engineering Corp.

Part # LXS6
Description  LX Series Lens Shields
PDF  2 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  BANNER [Banner Engineering Corp.]
Direct Link  https://www.bannerengineering.com/us/en.html
Logo BANNER - Banner Engineering Corp.

LXS6 Datasheet(HTML) 1 Page - Banner Engineering Corp.

  LXS6 Datasheet HTML 1Page - Banner Engineering Corp. LXS6 Datasheet HTML 2Page - Banner Engineering Corp.  
Zoom Inzoom in Zoom Outzoom out
 1 / 2 page
background image
Datasheet
The model LXS.. Lens Shield is a replaceable protective cover for the lens of an LX
Series sensor. The shield is made of 1.5 mm (0.06 inch) thick clear polycarbonate to
protect the sensor from damage due to weld flash or impact.
Shield models are available for every sensor length (see chart below). The shields attach
to the sensor with a pre-attached, adhesive-backed Neoprene foam gasket.
•
1.5 mm (0.06 inch) clear polycarbonate lens
•
Neoprene foam gasket
•
Easy to install
•
Available in lengths to protect 3.5-inch, 6.5-inch, and 12.5-inch long light screen
emitters and receivers.
Application Note: When shields are installed on both the emitter and receiver, excess
gain is reduced by 36 percent and maximum operating range is reduced by 20 percent.
Sensor Length
Lens Shield Model
Number
Part Number
Lens Shield Length
3.5 inches
LXS3
71351
3.87 inches
6.5 inches
LXS6
71352
6.87 inches
12.5 inches
LXS12
71353
12.87 inches
Installing the Lens Shield
Remove all dust, dirt, and oil from the metal surfaces on all four sides of the sensor lens using a mild detergent or window
cleaner and a soft cloth. Also clean the sensor lens and the lens shield, if needed.
Avoid cleaning agents containing alcohol; they will damage the sensor’s acrylic lens or the status indicators. If
in doubt about the composition of a cleaning agent, test a small area of the acrylic sensor lens below the active lens area
(at the bottom of the sensor, just above the cable connector) by applying the cleaning agent and allowing it to evaporate.
The foam gasket is pre-attached to the lens shield. Peel the paper backing from the foam gasket. Press one end of the lens
shield to the bottom end of the sensor, just above the status indicators, and apply pressure, moving slowly to the top end.
The width of the lens shield corresponds closely to the width of the sensor, so it is easy to keep it centered during
mounting. Peel away the protective coating from the lens shield’s outer surface.
Maintaining the Lens Shield
To prevent loss of excess gain, clean the shields when they become dirty. Remove dirt and/or oil from the front face of the
shield using a mild detergent or window cleaner and a soft cloth. Avoid industrial cleaning agents or cleaning agents
containing alcohol, as they may damage the shield material or the sensor.
Replacing the Lens Shield
Replace the shield when it becomes pitted or scratched, or excess gain will be decreased.
To remove, peel the lens shield away from the sensor starting at either end, and continuing to the opposite end. All or
most of the gasket will remain attached to the sensor; peel the gasket material away. Clean the sensor and install the new
lens shield as described in these instructions.
Banner Engineering Corp Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following
the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture
which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty
does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
LX Series Lens Shields
Original Document
113743 Rev. A
22 December 2015
113743


Similar Part No. - LXS6

ManufacturerPart #DatasheetDescription
logo
Banner Engineering Corp...
LXS6 BANNER-LXS6 Datasheet
746Kb / 6P
LX Series Part-Sensing Light Screen
LXS6 BANNER-LXS6 Datasheet
337Kb / 6P
LX Series Part-Sensing Light Curtain
09-Jul-25 Rev. I
More results

Similar Description - LXS6

ManufacturerPart #DatasheetDescription
logo
List of Unclassifed Man...
LX200VB1R0M ETC1-LX200VB1R0M Datasheet
840Kb / 5P
LXA/LX Series
logo
Qualtek Electronics Cor...
QSB-40-01 QUALTEK-QSB-40-01 Datasheet
348Kb / 1P
EMI Filter Shields for QLM Sleeves
logo
Dialight Corporation
C-17872 DIALIGHT-C-17872 Datasheet
76Kb / 1P
TRI-LEVEL LIGHTPIPE WITH SHIELDS
logo
MRV Communications, Inc...
LX-1000T MRV-LX-1000T Datasheet
559Kb / 2P
LX Series
LX-4000T MRV-LX-4000T Datasheet
408Kb / 2P
LX Series
LX5260 MRV-LX5260 Datasheet
799Kb / 2P
LX Series
logo
List of Unclassifed Man...
1783680000 ETC2-1783680000 Datasheet
429Kb / 5P
OMNIMATE Power - series LX LX 15.00/03/90 4.5SN GY BX
4DISPLAY-SHIELD-96 ETC2-4DISPLAY-SHIELD-96 Datasheet
14Mb / 13P
4Display Shields
logo
Panasonic Battery Group
EEF-LX PANASONICBATTERY-EEF-LX Datasheet
792Kb / 1P
EEF-GX and LX Series
logo
Sharma Electro Componen...
LX SHARMA-LX Datasheet
343Kb / 2P
LX Series
More results


Html Pages

1 2


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com