Specifications

Supply Voltage and Current

100 V ac to 240 V ac at 50 or 60 Hz

Indicators–maximum current per LED color:

•

60 mA at 100 V ac

•

55 mA at 120 V ac

•

40 mA at 240 V ac

Standard Audible Alarm: 30 mA maximum current

Sealed Audible Alarm: 35 mA maximum current

Omni-Directional Sealed Audible Alarm: 35 mA maximum current

Supply Protection Circuitry

Protected against transient voltages

Input Response Time

Indicator On/Off: 500 milliseconds maximum

Leakage Current Immunity

500 µA

Application Note: The use of relay output PLC is recommended since there

is no leakage current. Solid state output PLCs often have leakage current

above 1mA and, therefore, turn the light on in the off state. To counteract

the leakage current, a shunt resistor must be used. A resistor must be

applied from the neutral wire of the device to the hot wire of each channel of

the device.

Audible Alarm

Standard Audible Alarm: 2.7 kHz ± 500 Hz oscillation frequency; maximum

intensity 92 db at 1 meter (typical)

Sealed Audible Alarm: 2.9 kHz ± 250 Hz oscillation frequency; maximum

intensity 94 db at 1 meter (typical)

Omni-Directional Sealed Audible Alarm: 2.1 kHz ± 250 Hz oscillation

frequency; maximum intensity 99 db at 1m (3.3 ft) (typical)

Omni-Directional Sealed Audible Alarm with Intensity Adjustment: 2.1 kHz

± 250 Hz oscillation frequency; maximum intensity 95 dB at 1m (3.3 ft)

(typical)

Audible Adjustment

Standard Audible Alarm: Unscrew the cover (up to 1.5 turns max.) to adjust

the audible intensity. Do not exceed 1.5 turns or the cover may detach

during operation. For max. intensity, rotate the center plug 180°

counterclockwise to remove it.

Sealed Audible Alarm and Omni-Directional Sealed Audible Alarm with

Intensity Adjustment: Rotate the front cover until the desired intensity is

reached.

Typical Reduction in Sound Intensity with Audible Adjustment (maximum to

minimum):

•

Standard Audible: 30 dB

•

Sealed Audible: 20 dB

•

Omni-Directional Sealed Audible: 12 dB

Operating Conditions

Non-Audible: –40 °C to +50 °C (–40 °F to +122 °F)

Standard and Sealed Audible: –20 °C to +50 °C (–4 °F to +122 °F)

95% at +50 °C maximum relative humidity (non-condensing)

Environmental Rating

UL Type 4X Indoor and UL Type 13

Non-Audible and Sealed Audible: IEC IP67

Standard Audible: IEC IP50

Certifications

Indicators

LEDs or audible alarm are independently selected

Indicator Characteristics

Color

Dominant Wavelength (nm) or

Color Temperature (CCT)

Lumen Output (Typical

at 25 °C)

Green

525 nm

72

Red

625 nm

38

Yellow

590 nm

30

Blue

475 nm

28

White

5000 K

85

Connections

4- or 5-wire 2 m (6.5 ft) integral PVC cable, or 4- or 5-pin 150 mm (6 in) PVC

cable with a M12/Euro-style quick disconnect, depending on model

Models with a quick disconnect require a mating cordset

Construction

Bases and Covers: ABS

Light Segment: Polycarbonate

Vibration and Mechanical Shock

Meets IEC 60068-2-6 requirements (Vibration: 10 Hz to 55 Hz, 1.0 mm

amplitude, 5 minutes sweep, 30 minutes dwell)

Meets IEC 60068-2-27 requirements (Shock: 30G 11 ms duration, half sine

wave)

Required Overcurrent Protection

WARNING: Electrical connections must be

made by qualified personnel in accordance with

local and national electrical codes and

regulations.

Overcurrent protection is required to be provided by end product

application per the supplied table.

Overcurrent protection may be provided with external fusing or via Current

Limiting, Class 2 Power Supply.

Supply wiring leads < 24 AWG shall not be spliced.

For additional product support, go to

Supply Wiring (AWG)

Required Overcurrent Protection (Amps)

20

5.0

22

3.0

24

2.0

26

1.0

28

0.8

30

0.5

CL50 Universal AC Voltage Column Light

P/N 169424 Rev. G

www.bannerengineering.com - Tel: + 1 888 373 6767

3