CS42418 datasheet(16/67 Pages) CIRRUS

16 / 67 page

CS42418

the PLL. In this latter scenario the PLL output becomes the internal master clock. The supported PLL out-

put frequencies are shown in Table 3 below.

The serial bit clock, DAC_SCLK and/or ADC_SCLK, must be synchronous to the corresponding

DAC_LRCK/ADC_LRCK and be equal to 128x, 64x, 48x or 32x Fs depending on the interface format

selected and desired speed mode. One Line Mode #1 is supported in Slave Mode. One Line Mode #2 is

not supported. Refer to Table 4 for required clock ratios.

3.5

Digital Interfaces

3.5.1

Serial Audio Interface Signals

The CS42418 interfaces to an external Digital Audio Processor via two independent serial ports, the

DAC serial port, DAC_SP and the ADC serial port, ADC_SP. The digital output of the internal ADCs use

the ADC_SDOUT pin and can be configured to use either the ADC or DAC serial port timings. These con-

figuration bits and the selection of Single, Double or Quad Speed mode for DAC_SP and ADC_SP are

found in register “Functional Mode (address 03h)” on page 33.

The serial interface clocks, ADC_SCLK for ADC_SP and DAC_SCLK for DAC_SP, are used for trans-

mitting and receiving audio data. Either ADC_SCLK or DAC_SCLK can be generated by the CS42418

(master mode) or it can be input from an external source (slave mode). Master or Slave mode selection is

made using bits DAC_SP M/S and ADC_SP M/S in register “Misc Control (address 05h)” on page 36.

The Left/Right clock (ADC_LRCK or DAC_LRCK) is used to indicate left and right data frames and the

start of a new sample period. It may be an output of the CS42418 (master mode), or it may be generated

by an external source (slave mode). As described in later sections, particular modes of operation do allow

the sample rate, Fs, of the ADC_SP and the DAC_SP to be different, but must be multiples of each other.

The serial data interface format selection (left/right justified, I2S or one line mode) for the ADC serial port

data out pin, ADC_SDOUT, and the DAC input pins, DAC_SDIN1:4, is configured using the appropriate

Single Speed

Double Speed

Quad Speed

One Line Mode #1

OMCK/LRCK Ratio

256x, 512x

128x, 256x

128x

256x

SCLK/LRCK Ratio

32x, 48x, 64x, 128x

32x, 64x

128x

Table 4. Slave Mode Clock Ratios

Sample

Rate

(kHz)

PLL Output (MHz)

Single Speed

(4 to 50 kHz)

Double Speed

(50 to 100 kHz)

Quad Speed

(100 to 192 kHz)

256x

8.1920

44.1

11.2896

12.2880

16.3840

88.2

22.5792

24.5760

176.4

45.1584

192

49.1520

Table 3. Common PLL Output Clock Frequencies

CS42418 Datasheet(PDF) 16 Page - Cirrus Logic

CS42418 Datasheet(HTML) 16 Page - Cirrus Logic

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67

Datasheet Download

Link URL