ST7DALI datasheet(60/141 Pages) STMICROELECTRONICS

60 / 141 page

ST7DALI

60/141

12-BIT AUTORELOAD TIMER (Cont’d)

11.2.6 Register Description

TIMER CONTROL STATUS REGISTER

(ATCSR)

Read / Write

Reset Value: 0x00 0000 (x0h)

Bit 7 = Reserved.

Bit 6 = ICF Input Capture Flag.

This bit is set by hardware and cleared by software

by reading the ATICR register (a read access to

ATICRH or ATICRL will clear this flag). Writing to

this bit does not change the bit value.

0: No input capture

1: An input capture has occurred

Bit 5 = ICIE IC Interrupt Enable.

This bit is set and cleared by software.

0: Input capture interrupt disabled

1: Input capture interrupt enabled

Bits 4:3 = CK[1:0] Counter Clock Selection.

These bits are set and cleared by software and

cleared by hardware after a reset. They select the

clock frequency of the counter.

Note 1: PWM mode and Output Compare modes

are not available at this frequency.

Note 2: ATICR counter may return inaccurate re-

sults when read. It is therefore not recommended

to use Input Capture mode at this frequency.

Bit 2 = OVF Overflow Flag.

This bit is set by hardware and cleared by software

by reading the TCSR register. It indicates the tran-

sition of the counter from FFFh to ATR value.

0: No counter overflow occurred

1: Counter overflow occurred

Bit 1 = OVFIE Overflow Interrupt Enable.

This bit is read/write by software and cleared by

hardware after a reset.

0: OVF interrupt disabled.

1: OVF interrupt enabled.

Bit 0 = CMPIE Compare Interrupt Enable.

This bit is read/write by software and cleared by

hardware after a reset. It can be used to mask the

interrupt generated when the CMPF bit is set.

0: CMPF interrupt disabled.

1: CMPF interrupt enabled.

COUNTER REGISTER HIGH (CNTRH)

Read only

Reset Value: 0000 0000 (000h)

COUNTER REGISTER LOW (CNTRL)

Read only

Reset Value: 0000 0000 (000h)

Bits 15:12 = Reserved.

Bits 11:0 = CNTR[11:0] Counter Value.

This 12-bit register is read by software and cleared

by hardware after a reset. The counter is incre-

mented continuously as soon as a counter clok is

selected. To obtain the 12-bit value, software

should read the counter value in two consecutive

read operations, LSB first. When a counter over-

flow occurs, the counter restarts from the value

specified in the ATR register.

ICF

ICIE

CK1

CK0

OVF

OVFIE CMPIE

Counter Clock Selection

CK1

CK0

OFF

fLTIMER (1 ms timebase @ 8 MHz)

fCPU

32 MHz 2)

000

CNTR

CNTR9 CNTR8

CNTR7 CNTR6 CNTR5 CNTR4 CNTR3 CNTR2 CNTR1 CNTR0

ST7DALI Datasheet(PDF) 60 Page - STMicroelectronics

ST7DALI Datasheet(HTML) 60 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL