MODEL: M3LT

M3LT SPECIFICATIONS

ES-2661 Rev.13 Page 3/4

http://www.m-system.co.jp/

STANDARDS & APPROVALS

EU conformity:

EMC Directive

EMI EN 61000-6-4

EMS EN 61000-6-2

RoHS Directive

Approval:

UL/C-UL general safety requirements

(UL 61010-1, CAN/CSA-C22.2 No.1010-1)

EXTERNAL VIEW

Configuration DIP SW

4

5

6

■ FRONT VIEW

■ SIDE VIEW

8

SW2

SW1

SW3

7 6 5 4 3 2 1

ON

OFF

ON

OFF

4 3 2 1

ON

OFF

4 3 2 1

10 11 12

7

8

9

Configurator Jack

DOWN Button

UP Button

MODE Button

LED3 (LD3)

LED2 (LD2)

LED1 (LD1)

The DIP switch setting is required to select output types before setting a precise output range using the PC configurator

software.

For detailed information on the configuration and calibration, refer to the instruction manual.

INPUT TYPE, RANGE & ACCURACY

■ INPUT TYPE, RANGE & ACCURACY

Table 8

Thermocouple

°C

°F

MIN.

SPAN

MAXIMUM

RANGE

CONFORMANCE

RANGE

MIN.

SPAN

MAXIMUM

RANGE

CONFORMANCE

RANGE

(PR)

K (CA)

E (CRC)

20

20

20

0 to 1760

-270 to +1370

-270 to +1000

0 to 1760

-150 to +1370

-170 to +1000

±1.00

±0.25

±0.20

36

36

36

32 to 3200

-454 to +2498

-454 to +1832

32 to 3200

-238 to +2498

-274 to +1832

±1.80

±0.45

±0.36

J (IC)

T (CC)

B (RH)

20

20

20

-210 to +1200

-270 to +400

100 to 1820

-180 to +1200

-170 to +400

400 to 1760

±0.25

±0.25

±0.75

36

36

36

-346 to +2192

-454 to +752

212 to 3308

-292 to +2192

-274 to +752

752 to 3200

±0.45

±0.45

±1.35

R

S

C (WRe 5-26)

20

20

20

-50 to +1760

-50 to +1760

0 to 2315

200 to 1760

0 to 1760

0 to 2315

±0.50

±0.50

±0.80

36

36

36

-58 to +3200

-58 to +3200

32 to 4199

392 to 3200

32 to 3200

32 to 4199

±0.90

±0.90

±1.44

N

U

L

P(Platinel II)

20

20

20

20

-270 to +1300

-200 to +600

-200 to +900

0 to 1395

-130 to +1300

-200 to +600

-200 to +900

0 to 1395

±0.30

±0.20

±0.25

±0.25

36

36

36

36

-454 to +2372

-328 to +1112

-328 to +1652

32 to 2543

-202 to +2372

-328 to +1112

-328 to +1652

32 to 2543

±0.54

±0.36

±0.45

±0.45

*1. [Accuracy + Cold Junction Compensation Error 0.5°C (0.9°F)] or ±0.1% of span, whichever is greater.

If the selected output span equals to or narrower than the one-tenth of the maximum span, add 0.2%.