| Electronic Components Datasheet Search |
|
MAX4372 Datasheet(PDF) 2 Page - Maxim Integrated Products |
|
|
|||||||||||||||||||||||||||||
MAX4372 Datasheet(HTML) 2 Page - Maxim Integrated Products |
|
2 / 4 page ![]() MAX9928 Evaluation Kit 2 _______________________________________________________________________________________ Quick Start Recommended Equipment Before beginning, the following equipment is needed: • MAX9928 EV kit • 5V/10mA DC power supply • 12V/1A DC power supply • An electronic load capable of sinking 800mA (e.g., HP 6060B) • Two digital voltmeters Procedure The MAX9928 EV kit is fully assembled and tested. Follow the steps below to verify board operation. Caution: Do not turn on the power supply or the electronic load until all connections are completed. 1) Connect the positive terminal of the 5V supply to the VCC pad. Connect the negative terminal of the 5V supply to the GND pad. 2) Connect the positive terminal of the 12V supply to the RS+ pad. Connect the negative terminal of the 12V supply to the GND pad. 3) Set the electronic load to sink 500mA. 4) Connect the electronic load’s positive terminal to the RS- pad and the negative terminal to the GND pad. 5) Connect the first voltmeter across the OUT and the GND pads. 6) Connect the second voltmeter across the SIGN and the GND pads. 7) Turn on the power supplies. 8) Turn on the electronic load. 9) Verify that the OUT voltmeter reading is approximate- ly 2.5V and the SIGN voltmeter is approximately 5V. Take care not to load the internal 1M Ω pullup resistor on the SIGN pin when measuring this voltage. Detailed Description of Hardware The MAX9928 evaluation kit (EV kit) provides a proven design to evaluate the MAX9928 uni-/bidirectional, high-side, current-sense amplifier, which offers preci- sion accuracy specifications of VOS < 400µV and gain error < 1.0%. Output Voltage Calculation The MAX9928 EV kit is installed with a MAX9928FABT+, which has a gain of 5µA/mV. The current-sense resistor (RSENSE) value is 0.1Ω with ±1% tolerance. The VOUT is given by: VOUT =ILOAD x RSENSE x Gm x ROUT where Gm is the gain and ILOAD is the current load applied to the device. Vary ROUT to change the effec- tive voltage gain. Applying VCC and VRS+ Supply Voltages The normal operating range for VCC is 2.5V to 5.5V for MAX9928/MAX9929. The normal operating range for VCC is 2.7V to 28V for MAX4372. The normal input common-mode range at VRS+ and VRS- is -0.1V to +28V for MAX9928/MAX9929. The MAX4372 operates with an input range of 0V to 28V, but the total OUT error at 0V can be up to 28%. Measuring the Load Current The load current is measured as a voltage drop (VSENSE) across an external sense resistor. This volt- age is then amplified by the current-sense amplifier and presented as a current at its output pin and con- verted to a voltage by ROUT. Like all differential ampli- fiers, the output voltage has two components of error: an offset error and a gain error. The offset error affects accuracy at small VSENSE and a gain error affects accuracy at large VSENSE. By minimizing both offset and gain errors, accuracy can be optimized over a wide dynamic range. |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |