Electronic Components Datasheet Search
  English  ▼

X  

LTC7803 Datasheet(PDF) 9 Page - Analog Devices

Part # LTC7803
Description  40V Low IQ, Triple Output, 3-Phase Synchronous Step-Down Controller
PDF  36 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

LTC7803 Datasheet(HTML) 9 Page - Analog Devices

Back Button LTC7803 Datasheet HTML 5Page - Analog Devices LTC7803 Datasheet HTML 6Page - Analog Devices LTC7803 Datasheet HTML 7Page - Analog Devices LTC7803 Datasheet HTML 8Page - Analog Devices LTC7803 Datasheet HTML 9Page - Analog Devices LTC7803 Datasheet HTML 10Page - Analog Devices LTC7803 Datasheet HTML 11Page - Analog Devices LTC7803 Datasheet HTML 12Page - Analog Devices LTC7803 Datasheet HTML 13Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 9 / 36 page
background image
LTC7819
9
Rev. 0
For more information www.analog.com
PIN FUNCTIONS
MODE (Pin 1): Mode Select Input. This input, which acts
on all three channels, determines how the LTC7819 oper-
ates at light loads. Pulling this pin to ground selects Burst
Mode operation. An internal 100k resistor to ground also
invokes Burst Mode operation when the pin is floating.
Tying this pin to INTVCC forces continuous inductor cur-
rent operation. Tying this pin to INTVCC through a 100k
resistor selects pulse-skipping operation.
PGOOD1, PGOOD2, PGOOD3 (Pins 17, 7, 33): Open-
Drain Power Good Outputs. The VFB pin of each channel
is monitored to ensure that VOUT is in regulation. When a
channel’s VOUT is not within ±10% of its regulation point,
the corresponding PGOOD pin is pulled low.
RUN1, RUN2, RUN3 (Pins 10, 9, 8): Run Control Inputs
for Each Controller. Forcing any of these pins below
1.1V disables switching of the corresponding control-
ler. Forcing all of these pins below 0.7V shuts down the
entire LTC7819, reducing the quiescent current to approx-
imately 1.5µA. These pins can be tied to VIN for always-on
operation.
VPRG1 (Pin 16): Channel 1 Voltage Programming Pin.
This pin sets channel 1 to adjustable output voltage or to
a fixed output voltage. Floating this pin allows the channel
1 output to be programmed through the VFB1 pin using
external resistors, regulating VFB1 to the 0.8V reference.
Connecting this pin to GND or INTVCC programs the out-
put voltage to 3.3V or 5V (respectively), with VFB1 directly
connected to the output.
INTVCC (Pin 22): Output of the Internal 5.1V Low Dropout
Regulator. The driver and control circuits are powered by
this supply. Must be decoupled to ground with a minimum
of 4.7μF ceramic or tantalum capacitor.
EXTVCC (Pin 23): External Power Input to an Internal LDO
Connected to INTVCC. This LDO supplies INTVCC power,
bypassing the internal LDO powered from VIN whenever
EXTVCC is higher than 4.7V. See INTVCC Regulators in the
Applications Information section. Do not exceed 30V on
this pin. Connect this pin to ground if the EXTVCC LDO
is not used.
VIN (Pin 24): Main Bias Input Supply Pin. A bypass capac-
itor should be tied between this pin and ground.
PLLIN/SPREAD (Pin 34): External Synchronization Input
and Spread Spectrum Selection. When an external clock
is applied to this pin, the phase-locked loop will force
the rising TG1 signal to be synchronized with the ris-
ing edge of the external clock. When an external clock is
present, the regulators operate in pulse-skipping mode if
it is selected by the MODE pin, or in forced continuous
mode otherwise. When not synchronizing to an external
clock, tie this input to INTVCC to enable spread spectrum
dithering of the oscillator or to ground to disable spread
spectrum.
FREQ (Pin 40): Frequency Control Pin for the Internal
Oscillator. Connect to ground to set the switching fre-
quency to 380KHz. Connect to INTVCC to set the switch-
ing frequency to 2.25MHz. Frequencies between 100kHz
and 3MHz can be programmed using a resistor between
the FREQ pin and ground. Minimize the capacitance on
this pin.
BG1, BG2, BG3 (Pins 25, 21, 29): High Current Gate
Drives for Bottom N-Channel MOSFETs. Voltage swing at
these pins is from ground to INTVCC.
BOOST1, BOOST2, BOOST3 (Pins 26, 20, 30):
Bootstrapped Supplies to the Top Side Floating Drivers.
Connect capacitors between the corresponding BOOST
and SW pins for each channel. Also connect Schottky
diodes between the BOOST and INTVCC pins Voltage
swing at the BOOST pins is from INTVCC to (VIN+INTVCC).
SW1, SW2, SW3 (Pins 28, 19, 31): Switch Node
Connections to Inductors.
TG1, TG2, TG3 (Pins 27, 18, 32): High Current Gate
Drives for Top N-Channel MOSFETs. These are the out-
puts of floating drivers with a voltage swing of INTVCC
superimposed on the switch node voltage SW.
TRACK/SS1, TRACK/SS2, TRACK/SS3 (Pins 2, 15, 35):
External Tracking and Soft-Start Input. The LTC7819 regu-
lates the negative input of the Error Amplifier (EA−) volt-
age to the lesser of 0.8V or the voltage on the TRACK/



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com