GLS53 datasheet(94/109 Pages) EMERSON-NETWORKPOWER

94 / 109 page

GLT60 Series, GLT60-M Series Installation & Operating Instructions

Visit our Web site at www.solahd.com or contact Technical Support at (800) 377- 4384 with any questions

P/N: A272-199 Rev 0 5/12/09 Ref: 03361001433/03366200111/03366200551

To comply with the published safety standards, the following must be observed when using

this power supply:

Maximum ambient temperature for the power supply must not exceed 50°C.

When installing the power supply in the end-use equipment, special attention is

required to ensure safety compliance with the following safety standards: UL60950-1,

EN60950-1, IEC60950-1, and CSA22.2 No. 60950-1-03 for GLT62, GLT63, GLT64,

and GLT65; UL60601-1, EN60601-1, IEC60601-1, and CSA22.2 No. 60601-1-M90 for

GLT62-M and GLT63-M. The safety requirements include creepage distances, clear-

ances, and distance through insulation between primary wiring and earth or secondary

(SELV) wiring.

The power supply’s rated input voltage is automatically selected for GLT62, GLT63,

and GLT64. Please refer to the specification sheet for the input voltage range.

GLT65, GLT62-M, and GLT63-M are approved and certified for the rated voltage range

of 100 V ac to 250 V ac and/or 140 V dc to 300 V dc.

The maximum output power of the supply must not exceed the rating indicated in the

specification sheet.

The earth ground wire must be connected only to the point marked with the earth

ground symbol (on the unit).

The disconnection from the line must be in the end system.

Hazardous voltages exist in the primary circuits. Disconnect the power supply before

servicing.

When operating with a dc input voltage range, the unit input must be protected by a dc

rated fuse in the end-use installation system.

The internal fuse should only be replaced with a 3.15 A, 250 V ac, type SP0001.1009

manufactured by Schurter AG, type 2163.15 manufactured by Littelfuse, or type S501

manufactured by Cooper.

10. This power supply is not suitable for direct contact to the patient.

11. This equipment is considered Class I according to protection against electric shock.

12. This power supply is

marked following the provisions of the Low Voltage Directive,

2006/95/EC.

13. For technical assistance, contact SolaHD Technical Support at (800) 377- 4384 or

send an e-mail to tech@solahd.com. Please visit our Web site at www.solahd.com for

additional product information and specification sheets.

Mechanical Outline

R16

D16A

SK201

V Adj. Pot

SK2

GND

SK1

Connector PIN Designation

Input Connector

GLT62 (-M)

GLT63 (-M)

GLT64

GLT65

SK1

Neutral

Line

Output Connector

GLT62 (-M)

GLT63 (-M)

GLT64

GLT65

SK2

+12 V

+15 V

+12 V

+24 V

+5 V

Common

-12 V

-15 V

-5 V

+12 V

SK201

+Sense

-Sense

NOTe: Mounting holes M1 and M2 should be grounded for EMI purposes. Mounting hole M1 is a safety ground connection.

Output Ratings

Model

Output

Voltage (V)

Convection Cooling

30 CFM Forced Air Cooling

Max. Output

Current (A)

Max. Output

Power (W)

Max. Output

Current (A)

Max. Output

Power (W)

GLT62 (-M)

7.0

8.0

+12

3.0

3.5

-12

0.7

1.0

GLT63 (-M)

7.0

8.0

+15

2.8

3.3

-15

0.7

1.0

GLT64

7.0

8.0

+12

3.0

3.5

-5

0.7

1.0

GLT65

7.0

8.0

+24

1.5

2.0

+12

0.7

1.0

GLS53 Datasheet(PDF) 94 Page - Emerson Network Power

GLS53 Datasheet(HTML) 94 Page - Emerson Network Power

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL