Electronic Components Datasheet Search
  English  ▼

X  

SIP12108DB Datasheet(PDF) 13 Page - Vishay Siliconix

Part # SIP12108DB
Description  2.8 V to 5.5 V Input 5 A Synchronous Buck Regulator
PDF  17 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  VISHAY [Vishay Siliconix]
Direct Link  http://www.vishay.com
Logo VISHAY - Vishay Siliconix

SIP12108DB Datasheet(HTML) 13 Page - Vishay Siliconix

Back Button SIP12108DB Datasheet HTML 9Page - Vishay Siliconix SIP12108DB Datasheet HTML 10Page - Vishay Siliconix SIP12108DB Datasheet HTML 11Page - Vishay Siliconix SIP12108DB Datasheet HTML 12Page - Vishay Siliconix SIP12108DB Datasheet HTML 13Page - Vishay Siliconix SIP12108DB Datasheet HTML 14Page - Vishay Siliconix SIP12108DB Datasheet HTML 15Page - Vishay Siliconix SIP12108DB Datasheet HTML 16Page - Vishay Siliconix SIP12108DB Datasheet HTML 17Page - Vishay Siliconix  
Zoom Inzoom in Zoom Outzoom out
 13 / 17 page
background image
SiP12108, SiP12108A
www.vishay.com
Vishay Siliconix
S20-0484-Rev. C, 29-Jun-2020
13
Document Number: 62699
For technical questions, contact: powerictechsupport@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
INDUCTOR SELECTION
In order to determine the inductance, the ripple current must
first be defined. Cost, PCB size, output ripple, and efficiency
are all used in the selection process. Low inductor values
result in smaller size and allow faster transient performance
but create higher ripple current which can reduce efficiency.
Higher inductor values will reduce the ripple current while
compromising the efficiency (higher DCR) and transient
response.
The ripple current will also set the boundary for power-save
operation. The switcher will typically enter power-save
mode when the load current decreases to 1/2 of the ripple
current. For example, if ripple current is 1 A then power-save
operation will typically start at loads approaching 0.5 A.
Alternatively, if ripple current is set at 40 % of maximum load
current, then power-save will start for loads less than
~ 20 % of maximum current.
Inductor selection for the SiP12108 should be designed
where the ripple current is ~ 50 % in all situations with VIN
3.6 V and less.
For example 3.3 VIN to 1.2 VOUT at 1 MHz.
dI = V/L x dt = ((3.3 - 1.2)/0.33) x 0.36 = 2.3 A, %dI = 2.3/5
= 46 %.
For higher VIN > 3.6 V ripple current should be set to less
then 40 %.
For 5 VIN to 1.2 VOUT at 1 MHz dI = ((5 - 1.2)/0.68) x 0.36)
= 2 A, %dI = 2/5 = 40 %.
Output Capacitance Calculation
The output capacitance is usually chosen to meet transient
requirements. A worst-case load release, from maximum
load to no load at the exact moment when inductor current
is at the peak, determines the required capacitance. If the
load release is instantaneous (load changes from maximum
to zero in < 1/fSW μs), the output capacitor must absorb all
the inductor’s stored energy. This will approximately cause
a peak voltage on the capacitor according to the following
equation.
Assuming a peak voltage VPEAK of 1.3 V (100 mV rise upon
load release), and a 5 A load release, the required
capacitance is shown by the next equation.
If the load release is relatively slow, the output capacitance
can be reduced. Using MLCC ceramic capacitors we will
use 5 x 22 μF or 110 μF as the total output capacitance.
STABILITY CONSIDERATIONS
Using the output capacitance as a starting point for
compensation values. Then, taking Bode plots and transient
response measurements we can fine tune the compensation
values.
Setting the crossover frequency to 1/5 of the switching
frequency:
f0 = fsw/5 = 1 MHz/5 = 200 kHz
Setting the compensation zero at 1/5 to 1/10 the crossover
frequency for the phase boost:
Setting CC = 0.47 nF and solve for RC
SWITCHING FREQUENCY VARIATIONS
The switching frequency variation in COT can be mainly
attributed to the increase in conduction losses as the load
increases. The on time is “ideally constant” so the controller
must account for losses by reducing the off time which
increases the overall duty cycle. Hence the FSW will tend to
increase with load.
In power save mode (PSM) the IC will run in pulse skip mode
at light loads. As the load increases the FSW will increase
until it reaches the nominal set FSW. This transition occurs
approximately when the load reaches to 20 % of the full load
current.
DESIGN CONSIDERATION
For VOUT higher then UVLO (2.55 V typ.) and/or very slow VIN
slew rates. The IC may have difficulty in starting-up because
VIN level is limiting how fast VOUT can rise. In these situations
a divider for EN pin threshold (~1.15 V) derived from VIN
can be used. Allowing a higher VIN level before switching
begins and a smooth start-up. For example Rtop = 60K and
Rbot = 25K when VIN=4 V, EN level will be 1.18 V.
THERMAL DESIGN
The 16 pin package includes a thermal pad for much
better thermal performance when incorporated in the PCB
footprint. As shown in the PCB layout at the end of this
document. There are four vias evenly placed on the pad that
help transfer the heat to other layers. Tying the paddle to the
bottom layer through vias will provide the best thermal
performance.
C
OUTmin.
L x I
OUT +
1
2
--- x I
RIPPLEmax.


V
peak

2
- V
OUT

2
-------------------------------------------------------------------------
=
2
C
OUTmin. =
1 μH x (5 A + 0.5 x (0.81 A))
2
(1.3 V)
2 - (1.2 V)2
= 116.8 μF
F
Z =
1
2π x R
C x CC
=
F
0
5
R
C =
5
2π x C
C x F0
=
5
2π x 0.47 nF x 200K
= 8.469K



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com