LMV654 datasheet(3/5 Pages) NSC

3 / 5 page

5V DC Electrical Characteristics

Unless otherwise specified, all limits are guaranteed for T

J = 25˚C, V

+ = 5V, V− = 0V,V

O =VCM =V

+/2, and R

L > 1M

Ω. Bold-

face limits apply at the temperature extremes.

Symbol

Parameter

Conditions

Min

(Note 5)

Typ

(Note 4)

Max

(Note 5)

Units

Input Offset Voltage

–0.1

±1.8

TC V

Input Offset Average Drift

6.6

µV/˚C

Input Bias Current

(Note 6)

120

Input Offset Current

2.2

CMRR

Common Mode Rejection

Ratio

≤ V

≤ 4.0 V

100

PSRR

Power Supply Rejection Ratio

≤ V+ ≤ 5V, V

CM = 0.5V

2.7V

≤ V+ ≤ 5.5V, V

CM = 0.5V

CMVR

Input Common-Mode Voltage

Range

CMRR

≥ 80 dB

4.1

VOL

Large Signal Voltage Gain

0.3

≤ V

≤ 4.7V, R

L =2k

Ω to V+/2

0.3

≤ V

≤ 4.7V, R

L =10k

Ω to V+/2

Output Swing High

L =2k

Ω to V+/2

120

140

mV from

rail

L =10k

Ω to V+/2

Output Swing Low

L =2k

Ω to V+/2

110

130

L =10k

Ω to V+/2

Output Short Circuit Current

Sourcing to V

+/2

ID = 100 mV (Note 8)

18.5

Sinking from V

+/2

ID = −100 mV (Note 8)

Supply Current per Amplifier

119

µA

Slew Rate

V = +1, VO =1VPP

10% to 90% (Note 7)

3.2

V/µs

GBW

Gain Bandwidth Product

MHz

Input-Referred Voltage Noise

f = 100 kHz

nV/

f = 1 kHz

Input-Referred Current Noise

f = 100 kHz

0.1

pA/

f = 1 kHz

0.15

THD

Total Harmonic Distortion

f = 1 kHz, A

V =2,RL = 600

Ω

0.003

Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is

intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics Tables.

Note 2: Human Body Model is 1.5 k

Ω in series with 100 pF. Machine Model is 0Ω in series with 200 pF

Note 3: The maximum power dissipation is a function of TJ(MAX, θJA, and TA. The maximum allowable power dissipation at any ambient temperature is

PD =(TJ(MAX) -TA)/ θJA. All numbers apply for packages soldered directly onto a PC board.

Note 4: Typical values represent the most likely parametric norm at the time of characterization.

Note 5: Limits are 100% production tested at 25˚C. Limits over the operating temperature range are guaranteed through correlations using Statistical Quality Control

(SQC) method.

Note 6: Positive current corresponds to current flowing into the device.

Note 7: Slew rate is the average of the rising and falling slew rates.

Note 8: Short circuit test is a momentary test. Continuous source or sink currents higher than 10 mA are not recommended as they might permanently disable the

part.

LMV654 Datasheet(PDF) 3 Page - National Semiconductor (TI)

LMV654 Datasheet(HTML) 3 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5

Datasheet Download

Link URL