80

5

85

{0.7

{34

{15

MAU156

80

5

85

{0.8

{42

{12

MAU155

72

8

93

{2

{100

{5

MAU154

79

5

85

1

67

15

MAU153

79

5

85

1.5

84

12

MAU152

72

8

11

93

4

200

5

15

(13.5 ~ 16.5)

MAU151

80

5

53

{0.7

{34

{15

MAU129

79

5

53

{0.8

{42

{12

MAU128

76

5

55

{1

{56

{9

MAU127

72

8

58

{2

{100

{5

MAU126

79

5

53

1

67

15

MAU125

78

5

54

1.5

84

12

MAU124

76

5

54

2

110

9

MAU123

71

8

59

4

200

5

MAU122

73

8

7

49

5

260

3.3

24

(21.6 ~ 26.4)

MAU121

81

5

105

{0.7

{34

{15

MAU119

81

5

104

{0.8

{42

{12

MAU118

79

5

106

{1

{56

{9

MAU117

74

8

113

{2

{100

{5

MAU116

80

5

104

1

67

15

MAU115

80

5

105

1.5

84

12

MAU114

78

5

106

2

110

9

MAU113

73

8

114

4

200

5

MAU112

74

8

12

96

5

260

3.3

12

(10.8 ~ 13.2)

MAU111

79

7

258

{0.7

{34

{15

MAU109

78

7

258

{0.8

{42

{12

MAU108

77

8

262

{1

{56

{9

MAU107

72

10

278

{2

{100

{5

MAU106

78

7

258

1

67

15

MAU105

78

7

258

1.5

84

12

MAU104

76

8

260

2

110

9

MAU103

71

10

281

4

200

5

MAU102

73

10

30

235

5

260

3.3

5

(4.5 ~ 5.5)

MAU101

% (Typ.)

% (Max.)

mA (Typ.)

mA (Typ.)

mA

mA

VDC

VDC

@Max. Load

@No Load

@Max. Load

Min.

Max.

Efficiency

Load

Regulation

Input Current

Output Current

Output

Voltage

Input

Voltage

Model

Number

Model Selection Guide

Exceeding the absolute maximum ratings of the unit could cause damage.

These are not continuous operating ratings.

mW

450

---

Internal Power Dissipation

]

260

---

Lead Temperature (1.5mm from case for 10 Sec.)

VDC

30

-0.7

24VDC Input Models

VDC

18

-0.7

15VDC Input Models

VDC

18

-0.7

12VDC Input Models

VDC

9

-0.7

5VDC Input Models

Input Surge Voltage

( 1000 mS )

Unit

Max.

Min.

Parameter

Notes :

1. Specifications typical at Ta=+25], resistive load,

nominal input voltage, rated output current unless

otherwise noted.

2. Ripple & Noise measurement bandwidth is 0-20 MHz.

3. These power converters require a minimum output

loading to maintain specified regulation.

4. Operation under no-load conditions will not damage

these modules; however, they may not meet all

specifications listed.

5. All DC/DC converters should be externally fused at the

front end for protection.

6. Other input and output voltage may be available, please

contact factory.

7. Specifications subject to change without notice.

Absolute Maximum Ratings

MAU100 Series

2

MINMAX

REV:0 2005/04