www.stancor.com



R E l AY S A N D C O N TA C T O R S

Type 586 sPDT

D.C. Power Contactors – Type 

Engineering Design Data

operation in % of nom.

Breakdown Voltages

coil Rating

coil Voltage Rating

All Terminals - 60 hz Rms

contact material

electrical life

mechanical life

nominal

open

max.

magnetic

max.

contacts

oper.

oper. oper.

D.c. coil Rating

safe

opposite

same

To

oper. At

Per

oper. At

Per

Temp.

Type

(Watts)

Pick-up

operate

Polarity

Polarity Ground

Power

Pilot

Rated load min.

no load

min

°F

586

8 - SPNO

75%

110%

500

500

500

Silver Alloy

-

50,000

2

100,000

30

150

12 - SPDT

For outline drawings refer to page 57.

Temperature Range

–– -40˚F to 150˚F

Terminations

–– Contacts: 5/16"-24 UNF-2A thread

–– Coil: #10-32 UNF-2A thread

Recommended mounting

–– Vertical plane with coil terminals up.

hardware Torque specification

–– Contact Terminal: 60 inch-lbs., max.

–– Coil Terminal: 12-18 inch lbs.

–– Water Resistant

* Terminal Type: “4” = Isolated Coil

“6” = Isolated Coil

** Inrush Current: Current applied within the first 1/2 second of contact closure

coil

contact Rating-(Amps.)

DImensIons

sTAncoR

coil Resistance

Inductive load

Inches

PART

Duty Terminal Pole Bracket Volt. (ohms)

contact

Volt.

normally open

normally closed

case

Weight Agency

sec. nUmBeR

cycle

Type* Form

style

D.c. @25˚c

material D.c. continuous Inrush** continuous Inrush** l

W

h

(oz.) certif.

A

586-901 Continuous

4

SPNO Standard

6

5.3

Silver Alloy

6

200

600

-

-

3.69 3.30 2.90 24.0

-

586-902 Continuous

4

SPNO Standard 12

21.0

Silver Alloy

12

200

600

-

-

3.69 3.30 2.90 24.0

-

586-903 Continuous

4

SPNO Standard 15

32.8

Silver Alloy

15

200

600

-

-

3.69 3.30 2.90 24.0

-

B

586-905 Continuous

4

SPNO Standard 24

84.0

Silver Alloy

24

200

600

-

-

3.69 3.30 2.90 24.0

-

586-906 Continuous

4

SPNO Standard 36

189.0

Silver Alloy

36

200

600

-

-

3.69 3.30 2.90 24.0

-

586-907 Continuous

4

SPNO Standard 48

336.0

Silver Alloy

36

200

600

-

-

3.69 3.30 2.90 24.0

-

C

586-911 Continuous

6

SPDT Standard 12

13.2

Silver Alloy

12

200

600

100

300

4.61 3.30 2.90 26.0

-

586-914 Continuous

6

SPDT Standard 24

53.0

Silver Alloy

24

200

600

100

200

4.61 3.30 2.90 26.0

-

586-915 Continuous

6

SPDT Standard 36

120.0

Silver Alloy

36

200

600

100

200

4.61 3.30 2.90 26.0

-

Type 586 custom Design capabilities

–– Coil voltages 6 VDC through 48 VDC

–– High vibration

–– Please complete application data form on page 95 of this section.

note:

caution must be used in coil selection for use in 12 volt systems where battery charging may expose coil to continuous,

higher-than-rated voltage. stancor will not be responsible for consequences of misapplied solenoids.

Type 586 sPno