LTC2206 datasheet(6/32 Pages) LINER

6 / 32 page

LTC2207/LTC2206

22076fa

N – 7

N – 6

N – 5

N – 4

N – 3

ANALOG

INPUT

ENC–

ENC+

CLKOUT –

CLKOUT+

D0-D15, OF

22076 TD01

tAP

N + 1

N + 2

N + 4

N + 3

TIMING DIAGRAM

Note 1: Stresses beyond those listed under Absolute Maximum Ratings

may cause permanent damage to the device. Exposure to any Absolute

Maximum Rating condition for extended periods may affect device

reliability and lifetime.

Note 2: All voltage values are with respect to GND, with GND and OGND

shorted (unless otherwise noted).

Note 3: When these pin voltages are taken below GND or above VDD, they

will be clamped by internal diodes. This product can handle input currents

of greater than 100mA below GND or above VDD without latchup.

Note 4: VDD = 3.3V, fSAMPLE = 105MHz (LTC2207), 80MHz (LTC2206)

differential ENC+/ENC– = 2VP-P sine wave with 1.6V common mode,

input range = 2.25VP-P with differential drive (PGA = 0), unless otherwise

speciﬁed.

Note 5: Integral nonlinearity is deﬁned as the deviation of a code from a

“best ﬁt straight line” to the transfer curve. The deviation is measured from

the center of the quantization band.

Note 6: Offset error is the offset voltage measured from –1/2LSB when the

output code ﬂickers between 0000 0000 0000 0000 and 1111 1111 1111

1111 in 2’s complement output mode.

Note 7: Guaranteed by design, not subject to test.

Note 8: VDD = 3.3V, fSAMPLE = 105MHz (LTC2207) or 80MHz (LTC2206),

input range = 2.25VP-P with differential drive.

Note 9: Recommended operating conditions.

Note 10: The dynamic current of the switched capacitors analog inputs

can be large compared to the leakage current and will vary with the sample

rate.

Note 11: Leakage current will have higher transient current at power up.

Keep drive resistance at or below 1Kohm.

The ● denotes the speciﬁcations which apply over the full operating temperature

range, otherwise speciﬁcations are at TA = 25°C. (Note 4)

SYMBOL

PARAMETER

CONDITIONS

MIN

LTC2206

TYP

MAX

MIN

LTC2207

TYP

MAX

UNITS

Sampling Frequency

(Note 9)

●

105

MHz

ENC Low Time

Duty Cycle Stabilizer Off (Note 7)

Duty Cycle Stabilizer On (Note 7)

●

5.94

4.06

6.25

500

4.52

3.10

4.762

500

ENC High Time

Duty Cycle Stabilizer Off (Note 7)

Duty Cycle Stabilizer On (Note 7)

●

5.94

4.06

6.25

500

4.52

3.10

4.762

500

tAP

Sample-and-Hold

Aperture Delay

–0.7

ENC to DATA Delay

(Note 7)

●

1.3

2.7

1.3

2.7

ENC to CLKOUT Delay

(Note 7)

●

1.3

2.7

1.3

2.7

tSKEW

DATA to CLKOUT Skew

(tC-tD) (Note 7)

●

–0.6

0.6

–0.6

0.6

tOE

DATA Access time

Bus Relinquish time

CL = 5pF (Note 7)

(Note 7)

●

Pipeline

Latency

Cycles

TIMING CHARACTERISTICS

LTC2206 Datasheet(PDF) 6 Page - Linear Technology

LTC2206 Datasheet(HTML) 6 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

Datasheet Download

Link URL