Electronic Components Datasheet Search
  English  ▼

X  

MIC29371 Datasheet(PDF) 5 Page - Micrel Semiconductor

Part # MIC29371
Description  750mA Low-Dropout Voltage Regulator
PDF  12 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  MICREL [Micrel Semiconductor]
Direct Link  http://www.micrel.com
Logo MICREL - Micrel Semiconductor

MIC29371 Datasheet(HTML) 5 Page - Micrel Semiconductor

  MIC29371 Datasheet HTML 1Page - Micrel Semiconductor MIC29371 Datasheet HTML 2Page - Micrel Semiconductor MIC29371 Datasheet HTML 3Page - Micrel Semiconductor MIC29371 Datasheet HTML 4Page - Micrel Semiconductor MIC29371 Datasheet HTML 5Page - Micrel Semiconductor MIC29371 Datasheet HTML 6Page - Micrel Semiconductor MIC29371 Datasheet HTML 7Page - Micrel Semiconductor MIC29371 Datasheet HTML 8Page - Micrel Semiconductor MIC29371 Datasheet HTML 9Page - Micrel Semiconductor Next Button
Zoom Inzoom in Zoom Outzoom out
 5 / 12 page
background image
MIC2937A/29371/29372
Micrel, Inc.
May 2006
5
MIC2937A/29371/29372
Note 1: Absolute maximum ratings indicate limits beyond which damage to the component may occur. Electrical specifications do not
apply when operating the device outside of its rated operating conditions. The maximum allowable power dissipation is a function of the
maximum junction temperature, T
J (MAX), the junction-to-ambient thermal resistance, θJA, and the ambient temperature, TA. The maximum
allowable power dissipation at any ambient temperature is calculated using: P
(MAX) = (TJ(MAX) – TA) / θJA. Exceeding the maximum allowable
power dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown.
Note 2: Output voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature range.
Note 3: Regulation is measured at constant junction temperature using low duty cycle pulse testing. Changes in output voltage due to
heating effects are covered by the thermal regulation specification.
Note 4: Dropout Voltage is defined as the input to output differential at which the output voltage drops 100 mV below its nominal value
measured at 1V differential. At low values of programmed output voltage, the minimum input supply voltage of 4.3V over temperature must
be taken into account. The MIC2937A operates down to 2V of input at reduced output current at 25°C.
Note 5: Ground pin current is the regulator quiescent current. The total current drawn from the source is the sum of the load current
plus the ground pin current.
Note 6: The MIC2937A family features fold-back current limiting. The short circuit (V
OUT = 0V) current limit is less than the maximum
current with normal output voltage.
Note 7: Thermal regulation is defined as the change in output voltage at a time T after a change in power dissipation is applied, exclud-
ing load or line regulation effects. Specifications are for a 200mA load pulse at V
IN = 20V (a 4W pulse) for T = 10ms.
Note 8: V
REF ≤ VOUT ≤ (VIN – 1 V), 4.3V ≤ VIN ≤ 26V, 5mA < IL ≤ 750 mA, TJ ≤ TJ MAX.
Note 9: Comparator thresholds are expressed in terms of a voltage differential at theAdjust terminal below the nominal reference voltage
measured at 6V input (for a 5V regulator). To express these thresholds in terms of output voltage change, multiply by the error amplifier
gain = V
OUT /VREF = (R1 + R2)/R2. For example, at a programmed output voltage of 5V, the Error output is guaranteed to go low when
the output drops by 95 mV x 5V/1.235 V = 384 mV. Thresholds remain constant as a percent of VOUT as VOUT is varied, with the dropout
warning occurring at typically 5% below nominal, 7.7% guaranteed.
Note 10: Circuit of Figure 3 with R1 ≥ 150kΩ. V
SHUTDOWN ≥ 2V and VIN ≤ 26V,VOUT = 0.
Note 11: When used in dual supply systems where the regulator load is returned to a negative supply, the output voltage must be diode
clamped to ground.
Note 12: Maximum positive supply voltage of 60V must be of limited duration (< 100ms) and duty cycle ( ≤ 1%). The maximum continu-
ous supply voltage is 26V.
FEEDBACK
SENSE
Q15A
OUT
Q24
Q26
R27
V TAP
R28
R18
20 kΩ
Q25
Q23
Q22
R15
100 kΩ
R16
30 kΩ
Q29
Q28
R17
10Ω
R21 8 Ω
R17
12 kΩ
Q31
Q30
R23 60 k Ω
SHDN
R24
50 kΩ
R22
150 kΩ
Q21
Q19
C2
40 pF
R14
350
k Ω
Q14
R13
100
k Ω
Q18
R12
110
k Ω
Q20
Q9
Q15B
Q8
Q7
R11
20.6
k Ω
Q5
R8
31.4 k Ω
R10
150
k Ω
R9
27.8 k Ω
Q11
Q12
Q13
R6
140
k Ω
R5
180
k Ω
R4
13 kΩ
R3
50 kΩ
Q2
C1
20
pF
Q4
Q3
R11
18
k Ω
Q6
Q1
10
R1
20 kΩ
R2
50 kΩ
Q41
R30
30
k Ω
Q40
Q34
GND
Q36
Q37
R25
2.8 kΩ
Q38
ERROR
R26
60 kΩ
Q39
Q42
Q16
Q17
50 kΩ
10 kΩ
IN
DENOTES CONNECTION ON
MIC2937A-xx AND MIC29371-xx
VERSIONS ONLY
Schematic Diagram



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com