70 WATTS

SINGLE/MULTI OUTPUT AC-DC

FEATURES:

CHASSIS/COVER

OPEN FRAME

SAFETY SPECIFICATIONS

Underwriters Laboratories

File E137708/E140259

UL 62368-1:2014, 2nd Edition

CAN/CSA-C22.2 No. 62368-1-14

AAMI/ANSI ES60601-1:2005/(R) 2012

CAN/CSA-C22.2 No. 60601-1:2014

CB Reports/Certificates (including all

National and Group Deviations)

IEC 62368-1:2014, 2nd Edition

IEC 60601-1:2005/A1:2012

TUV SUD America

EN 62368-1:2014, 2nd Edition

EN 60601-1:2006/A1:2013

Low Voltage Directive

(2014/35/EU of February 2014)

RoHS Directive (Recast)

(2011/65/EU of June 2011)

Electrical Equipment (Safety) Regulations 2016 SI No. 1101

Restriction of the Use of Certain Hazardous Substances in EEE Regulations

2012 SI No. 3032 + 2019 SI No.492

MODEL LISTING

MODEL NO. OUTPUT 1

OUTPUT 2

OUTPUT 3

OUTPUT 4

REL-70-4001

+3.3V/6A

+5V/5A

+12V/2A(21)

-12V/2A(21)

REL-70-4002

+5V/6A

+3.3V/5A

+12V/2A(21)

-12V/2A(21)

REL-70-4003

+5V/6A

+3.3V/5A

+15V/2A(21)

-15V/2A(21)

REL-70-4004

+5V/6A

-5V/5A

+12V/2A(21)

-12V/2A(21)

REL-70-4005

+5V/6A

-5V/5A

+15V/2A(21)

-15V/2A(21)

REL-70-4006

+5V/6A

+24V/2A

+12V/2A(21)

-12V/2A(21)

REL-70-4007

+5V/6A

+24V/2A

+15V/2A(21)

-15V/2A(21)

REL-70-4009

6.7V/5A

5V/4A

+15V/2A(21)

-15V/2A(21)

REL-70-3001

+5V/6A

+12V/2A

-12V/2A(21)

REL-70-3002

+5V/6A

+15V/2A

-15V/2A(21)

REL-70-3003

+5.1V/6A

+7.5V/2A

-7.5V/2A(21)

REL-70-3004

+3.3V/6A

+7V/5A

+12V/2A(21)

REL-70-2001

+3.3V/6A

+5V/5A

REL-70-2002

+5V/6A

+12V/4A

REL-70-2003

+5V/6A

+24V/2A

REL-70-2004

+12V/3A

-12V/3A

REL-70-2005

+15V/3A

-15V/2A

REL-70-2006

+5.5V/6A

-5.5V/5A

REL-70-1001

2.5V/14A(20)

REL-70-1002

3.3V/14A(20)

REL-70-1003

5V/14A(20)

REL-70-1004

12V/5.8A

REL-70-1005

15V/4.7A

REL-70-1006

24V/2.9A

REL-70-1007

28V/2.5A

REL-70-1008

48V/1.5A

ORDERING INFORMATION

Consult factory for alternate output configurations.

Consult factory for positive, negative or floating outputs.

Please specify the following optional features when ordering:

CH - Chassis

I/O - Isolated Outputs

CO - Cover

TS - Terminal Strip

REL-70

OUTPUT SPECIFICATIONS

Total Output Power at 50°C(1)

50W

Convection Cooled(16)(18)

(See Derating Chart)

70W

300LFM Forced-Air Cooled(15)(17)(19)

Output Voltage Centering

Output 1:

 0.5%

(All outputs at 50% load)

Output 2,3,4:

 5.0%

Output Voltage Adjust Range

Output 1:

95 - 105%

Load Regulation

Output 1:

0.5%

(10-100% load change)

Output 2:

5.0%

(4001-5)

8.0%

(2001)

8.0%

Output 3:

5.0%

Output 4:

5.0%

Source Regulation

Outputs 1 – 4:

0.5%

Cross Regulation

Outputs 2 – 4:

5.0%

Output Noise

Outputs 1 – 4:

1.0%

Turn on Overshoot

None

Transient Response

Outputs 1 – 4

Voltage Deviation

5.0%

Recovery Time

500

S

Load Change

50% to 100%

Output Overvoltage Protection

Output 1:

110% to 150%

Output Overpower Protection

110-160% rated Pout, cycle on/off, auto recovery

Hold Up Time

16mS min., Full Power, 85V Input

Start Up Time

4 Seconds, 120V Input

INPUT SPECIFICATIONS

Protection Class

I

Source Voltage

85 – 264 Volts AC

Frequency Range

47 – 63 Hz

Peak Inrush Current

40A

Efficiency

78% Typ., Full Power, 230V, varies by model

Power Factor

0.95 (Full Power, 230V)

ENVIRONMENTAL SPECIFICATIONS

Ambient Operating

0

C to + 70C

Temperature Range

Derating: See Power Rating Chart

Ambient Storage Temp. Range

- 40

C to + 85C

Temperature Coefficient

Outputs 1 – 4:

0.02%/

C

Altitude

3,000m ASL – Operating – Medical 60601-1

5,000m ASL – Operating – ITE/AV – 62368-1

12,192m ASL – Non-Operating

GENERAL SPECIFICATIONS

Means of Protection

Primary to Secondary

2MOPP (Means of Patient Protection)

Primary to Ground

1MOPP (Means of Patient Protection)

Secondary to Ground

Operational Insulation(Consult factory for 1MOPP)

Dielectric Strength(8, 9)

Reinforced Insulation

5656 VDC, Primary to Secondary

Basic Insulation

2121 VDC, Primary to Ground

Operational Insulation

707 VDC, Secondary to Ground

Leakage Current

Earth Leakage

<300µA NC, <1000µA SFC

Touch Current

<100µA NC, <500µA SFC

Power Fail Signal(14)

Logic low with input power failure 10 ms

minimum prior to Output 1 dropping 1%

Remote Sense (singles only)(10)

250mV compensation of output cable losses

Mean-Time Between Failures

100,000 Hours min., MIL-HDBK-217F, 25° C, GB

Weight

0.60 Lbs.

Open Frame

1.00 Lbs.

Chassis and Cover

EMC SPECIFICATIONS (IEC 60601-1-2:2014, 4TH ED./IEC 61000-6-2:2005)

Electrostatic Discharge

EN 61000-4-2

8KV contact / 15KV air discharge

A

Radiated Electromagnetic Field

EN 61000-4-3

80MHz-2.7GHz, 10V/m, 80% AM

A

Electrical Fast Transients/Bursts

EN 61000-4-4

2 KV, 5KHz/100KHz

A

Surge Immunity

EN 61000-4-5

2 KV line to earth / 1 KV line to line A

Conducted Immunity

EN 61000-4-6

0.15 to 80MHz, 10V, 80% AM

A

Magnetic Field Immunity

EN 61000-4-8

30A/m, 60 Hz.

A

Voltage Dips

EN 61000-4-11 0% UT, 0.5 cycles, 0-315° 100/240V A/A

0% UT, 1 cycles, 0°

100/240V A/A

40% UT, 10/12 cycles, 0° 100/240V B/A

70% UT, 25/30 cycles, 0° 100/240V B/A

Voltage Interruptions

EN 61000-4-11 0% UT, 300 cycles, 0°

100/240V B/B

Radiated Emissions

EN 55011/32

Class B

Conducted Emissions

EN 55011/32

Class B

Harmonic Current Emissions

EN 61000-3-2

Class A

Voltage Fluctuations/Flicker

EN 61000-3-3

Compliant

All specifications are maximum at 25°C/70W unless otherwise stated, may vary by model and are

subject to change without notice.

• Compact 2.5 x 4.5" x 1.2" Size

• 2 Year Warranty

• Universal 85-264V Input

• One to Four Outputs

• High Efficiency

• 0-70°C Operating Temperature

• IEC 60601-1 3rd ed. Medical Cert.

• IEC 62368-1 2nd Certification

• IEC 60601-1-2 4th ed. EMC

• Class B Emissions per EN55011/32

• RoHS Compliant

• Optional Chassis/Cover

INTEGRATED

POWER DESIGNS 300 Stewart Road ■ Wilkes-Barre, PA 18706 ■ Phone: (570) 824-4666 ■ Fax: (570) 824-4843 ■ Email: sales@ipdpower.com ■ Web: www.ipdpower.com