MPF4393RLRPG datasheet(4/6 Pages) ONSEMI

4 / 6 page

MPF4392, MPF4393

http://onsemi.com

Figure 5. Switching Time Test Circuit

2.0

3.0

5.0

7.0

0.5

1.0

3.0

5.0

0.3

0.1

0.05

0.03

VR, REVERSE VOLTAGE (VOLTS)

170

−10

−40

140

−70

1.8

1.0

2.0

1.2

1.4

1.6

0.8

0.6

0.4

Tchannel, CHANNEL TEMPERATURE (°C)

1.5

1.0

110

VDD

VGG

RGG

RGEN

VGEN

OUTPUT

INPUT

SET VDS(off) = 10 V

INPUT PULSE

tr ≤ 0.25 ns

tf ≤ 0.5 ns

PULSE WIDTH = 2.0

DUTY CYCLE

≤ 2.0%

RGG & RK

RD′ = RD(RT + 50)

RD + RT + 50

Figure 6. Typical Forward Transfer Admittance

NOTE 1

The switching characteristics shown above were measured using a

test circuit similar to Figure 5. At the beginning of the switching

interval, the gate voltage is at Gate Supply Voltage (−VGG). The

Drain−Source Voltage (VDS) is slightly lower than Drain Supply

Voltage (VDD) due to the voltage divider. Thus Reverse Transfer

Capacitance (Crss) or Gate−Drain Capacitance (Cgd) is charged to

VGG + VDS.

During the turn−on interval, Gate−Source Capacitance (Cgs)

discharges through the series combination of RGen and RK. Cgd

must discharge to VDS(on) through RG and RK in series with the

parallel combination of effective load impedance (R

′D) and

Drain−Source Resistance (rds). During the turn−off, this charge

flow is reversed.

Predicting turn−on time is somewhat difficult as the channel

resistance rds is a function of the gate−source voltage. While Cgs

discharges, VGS approaches zero and rds decreases. Since Cgd

discharges through rds, turn−on time is non−linear. During turn−off,

the situation is reversed with rds increasing as Cgd charges.

The above switching curves show two impedance conditions:

1) RK is equal to RD

′ which simulates the switching behavior of

cascaded stages where the driving source impedance is normally the

load impedance of the previous stage, and 2) RK = 0 (low

impedance) the driving source impedance is that of the generator.

Figure 7. Typical Capacitance

ID, DRAIN CURRENT (mA)

2.0

5.0

3.0

7.0

0.5

1.0

3.0

7.0

5.0

0.7

2.0

120

160

200

1.0

3.0

5.0

2.0

VGS, GATE−SOURCE VOLTAGE (VOLTS)

4.0

6.0

7.0

8.0

Tchannel = 25°C

(Cds IS NEGLIGIBLE)

Cgs

Tchannel = 25°C

VDS = 15 V

Figure 8. Effect of Gate−Source Voltage

On Drain−Source Resistance

Figure 9. Effect of Temperature On

Drain−Source On−State Resistance

MPF4392

MPF4393

Cgd

ID = 1.0 mA

VGS = 0

IDSS

= 10

50 mA

75 mA 100 mA

125 mA

Tchannel = 25°C

MPF4393RLRPG Datasheet(PDF) 4 Page - ON Semiconductor

MPF4393RLRPG Datasheet(HTML) 4 Page - ON Semiconductor

Html Pages

1 2 3 4 5 6

Datasheet Download

Link URL