| Electronic Components Datasheet Search |
|
ATA6602 Datasheet(PDF) 21 Page - ATMEL Corporation |
|
|
|||||||||||||||||||||||||||||
ATA6602 Datasheet(HTML) 21 Page - ATMEL Corporation |
|
21 / 362 page ![]() 21 4921C–AUTO–01/07 ATA6602/ATA6603 7.4 At VCC undervoltage threshold the state switches back to Pre Normal Mode Referred to VCC V S > 5.5 27 VthunS 3.9 4.4 V A 7.5 Hysteresis of undervoltage threshold Referred to VCC V S > 5.5V 27 Vhys thun 40 mV D 7.6 Output current limitation V S > 0V 27 I VCCs –200 –130 mA A 8 LIN Bus Driver: Bus Load Conditions: Load1 (Small): 1 nF, 1 k Ω; Load2 (Large): 10 nF, 500Ω; RRXD = 5 kΩ; C RXD = 20 pF 10.5, 10.6 and 10.7 Specify the Timing Parameters for Proper Operation at 20 Kbps 8.1 Driver recessive output voltage Load1/Load2 18 V BUSrec 0.9 V S V S VA 8.2 Driver dominant voltage V VS =7V R load =500Ω 18 V_LoSUP 1.2 V A 8.3 Driver dominant voltage V VS =18V Rload =500Ω 18 V _HiSUP 2V A 8.4 Driver dominant voltage V BUSdom_DRV_LoSUP VVS = 7V R load = 1000Ω 18 V _LoSUP_1k 0.6 V A 8.5 Driver dominant voltage V VS = 18V R load =1000Ω 18 V_HiSUP_1k_ 0.8 V A 8.6 Pull-up resistor to VS The serial diode is mandatory 18 R LIN 20 30 60 k Ω A 8.7 Self-adapting current limitation V Bus =VBatt_max T j = 125°C Tj = 27°C T j = –40°C 18 IBUS_LIM 52 100 120 110 170 230 mA mA mA A 8.8 Input leakage current at the receiver including pull-up resistor as specified Input leakage current Driver off VBUS =0V V Battery =12V 18 I BUS_PAS_dom –1 mA A 8.9 Leakage current LIN recessive Driver off 8V < VBattery <18V 8V < VBUS < 18V V BUS ≥ VBatt 18 I BUS_PAS_rec 15 20 µA A 8.10 Leakage current when control unit disconnected from ground. Loss of local ground must not affect communication in the residual network GND Device = VS VBattery = 12V 0V < VBUS < 18V 18 IBUS_NO_gnd –10 0.5 10 µA A 8.11 Node has to sustain the current that can flow under this condition. Bus must remain operational under this condition V Battery disconnected VSUP_Device = GND 0V < VBUS < 18V 18 IBUS 0.5 3 µA A 3.5 Electrical Characteristics (Continued) 5V < VS < 18V, Tcase = –40°C to +125°C No. Parameters Test Conditions Pin Symbol Min. Typ. Max. Unit Type* *) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |