HA5022IP datasheet(7/17 Pages) INTERSIL

7 / 17 page

Application Information

Optimum Feedback Resistor

The plots of inverting and non-inverting frequency response,

see Figure 11 and Figure 12 in the Typical Performance

Curves section, illustrate the performance of the HA5022 in

various closed loop gain configurations. Although the

bandwidth dependency on closed loop gain isn’t as severe

as that of a voltage feedback amplifier, there can be an

appreciable decrease in bandwidth at higher gains. This

decrease may be minimized by taking advantage of the

current feedback amplifier’s unique relationship between

bandwidth and RF . All current feedback amplifiers require a

feedback resistor, even for unity gain applications, and RF,

in conjunction with the internal compensation capacitor, sets

the dominant pole of the frequency response. Thus, the

amplifier’s bandwidth is inversely proportional to RF. The

HA5022 design is optimized for a 1000

Ω R

F at a gain of +1.

Decreasing RF in a unity gain application decreases stability,

resulting in excessive peaking and overshoot. At higher

gains the amplifier is more stable, so RF can be decreased

in a trade-off of stability for bandwidth.

The table below lists recommended RF values for various

gains, and the expected bandwidth.

PC Board Layout

The frequency response of this amplifier depends greatly on

the amount of care taken in designing the PC board. The

use of low inductance components such as chip resistors

and chip capacitors is strongly recommended. If leaded

components are used the leads must be kept short

especially for the power supply decoupling components and

those components connected to the inverting input.

Attention must be given to decoupling the power supplies. A

large value (10

µF) tantalum or electrolytic capacitor in

parallel with a small value (0.1

µF) chip capacitor works well

in most cases.

A ground plane is strongly recommended to control noise.

Care must also be taken to minimize the capacitance to

ground seen by the amplifier’s inverting input (-IN). The

larger this capacitance, the worse the gain peaking, resulting

in pulse overshoot and possible instability. It is

recommended that the ground plane be removed under

traces connected to -IN, and that connections to -IN be kept

as short as possible to minimize the capacitance from this

node to ground.

Driving Capacitive Loads

Capacitive loads will degrade the amplifier’s phase margin

resulting in frequency response peaking and possible

oscillations. In most cases the oscillation can be avoided by

placing an isolation resistor (R) in series with the output as

shown in Figure 6.

The selection criteria for the isolation resistor is highly

dependent on the load, but 27

Ω has been determined to be

a good starting value.

Power Dissipation Considerations

Due to the high supply current inherent in dual amplifiers,

care must be taken to insure that the maximum junction

temperature (TJ, see Absolute Maximum Ratings) is not

exceeded. Figure 7 shows the maximum ambient

temperature versus supply voltage for the available package

styles (PDIP, SOIC). At VS = ±5V quiescent operation both

package styles may be operated over the full industrial

range of -40oC to 85oC. It is recommended that thermal

calculations, which take into account output power, be

performed by the designer.

Enable/Disable Function

When enabled the amplifier functions as a normal current

feedback amplifier with all of the data in the electrical

specifications table being valid and applicable. When

GAIN

(ACL)RF (Ω)

BANDWIDTH

(MHz)

-1

750

100

1000

125

681

1000

+10

383

-10

750

VIN

VOUT

FIGURE 6. PLACEMENT OF THE OUTPUT ISOLATION

RESISTOR, R

100

Ω

140

130

120

110

100

111315

SUPPLY VOLTAGE (

±V)

PDIP

SOIC

FIGURE 7. MAXIMUM OPERATING AMBIENT

TEMPERATURE vs SUPPLY VOLTAGE

HA5022

HA5022IP Datasheet(PDF) 7 Page - Intersil Corporation

HA5022IP Datasheet(HTML) 7 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

Datasheet Download

Link URL