Philips Semiconductors

Product specification

SA606

Low-voltage high performance mixer FM IF system

1997 Nov 07

4

SYMBOL

PARAMETER

TEST CONDITIONS

LIMITS

UNITS

SYMBOL

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNITS

THD

Total harmonic distortion

-35

-50

dB

S/N

Signal-to-noise ratio

No modulation for noise

62

dB

RF level = -118dBm

0.3

.80

V

RF level = -68dBm

.70

1.1

1.80

V

RF level = -23dBm

1.20

1.8

2.50

V

RSSI range

90

dB

RSSI accuracy

+1.5

dB

IF input impedance

Pin 18

1.3

1.5

k

Ω

IF output impedance

Pin 16

0.3

k

Ω

Limiter input impedance

Pin 14

1.3

1.5

k

Ω

Limiter output impedance

Pin 11

0.3

k

Ω

Limiter output voltage

Pin 11

130

RF/IF section (int LO)

Audio level

120

System RSSI output

2.2

V

System SINAD sensitivity

RF level = -117dBm

12

dB

CIRCUIT DESCRIPTION

The SA606 is an IF signal processing system suitable for second IF

systems with input frequency as high as 150MHz. The bandwidth of

the IF amplifier and limiter is at least 2MHz with 90dB of gain. The

gain/bandwidth distribution is optimized for 455kHz, 1.5k

Ω source

applications. The overall system is well-suited to battery operation

as well as high performance and high quality products of all types.

The input stage is a Gilbert cell mixer with oscillator. Typical mixer

characteristics include a noise figure of 6.2dB, conversion gain of

17dB, and input third-order intercept of -9dBm. The oscillator will

operate in excess of 200MHz in L/C tank configurations. Hartley or

Colpitts circuits can be used up to 100MHz for xtal configurations.

Butler oscillators are recommended for xtal configurations up to

150MHz.

The output impedance of the mixer is a 1.5k

Ω resistor permitting

direct connection to a 455kHz ceramic filter. The input resistance of

the limiting IF amplifiers is also 1.5k

Ω. With most 455kHz ceramic

filters and many crystal filters, no impedance matching network is

necessary. The IF amplifier has 43dB of gain and 5.5MHz

bandwidth. The IF limiter has 60dB of gain and 4.5MHz bandwidth.

To achieve optimum linearity of the log signal strength indicator,

there must be a 12dB(v) insertion loss between the first and second

IF stages. If the IF filter or interstage network does not cause

12dB(v) insertion loss, a fixed or variable resistor or an L pad for

simultaneous loss and impedance matching can be added between

the first IF output (Pin 16) and the interstage network. The overall

gain will then be 90dB with 2MHz bandwidth.

The signal from the second limiting amplifier goes to a Gilbert cell

quadrature detector. One port of the Gilbert cell is internally driven

by the IF. The other output of the IF is AC-coupled to a tuned

quadrature network. This signal, which now has a 90

relationship to the internal signal, drives the other port of the

multiplier cell.

The demodulated output of the quadrature drives an internal op

amp. This op amp can be configured as a unity gain buffer, or for

simultaneous gain, filtering, and 2nd-order temperature

compensation if needed. It can drive an AC load as low as 5k

Ω with

a rail-to-rail output.

A log signal strength completes the circuitry. The output range is

greater than 90dB and is temperature compensated. This log signal

strength indicator exceeds the criteria for AMPs or TACs cellular

telephone. This signal drives an internal op amp. The op amp is

capable of rail-to-rail output. It can be used for gain, filtering, or

2nd-order temperature compensation of the RSSI, if needed.