| Electronic Components Datasheet Search |
|
MAX2055 Datasheet(PDF) 2 Page - Maxim Integrated Products |
|
|
|||||||||||||||||||||||||||||
MAX2055 Datasheet(HTML) 2 Page - Maxim Integrated Products |
|
2 / 7 page ![]() MAX2055 Evaluation Kit 2 _______________________________________________________________________________________ Quick Start The MAX2055 EV kit is fully assembled and factory test- ed. Follow the instructions in the Connections and Setup section for proper device evaluation. Table 1 lists the attenuation setting vs. gain-control bit. Test Equipment Required • DC supply capable of delivering 5.25V and 400mA of continuous current • HP 8648 (or equivalent) signal source • HP 8561E (or equivalent) spectrum analyzer capa- ble of covering the MAX2055’s frequency range, as well as a few harmonics • Two digital multimeters (DMMs) to monitor VCC and ICC, if desired • HP 8753D (or equivalent) network analyzer to mea- sure return loss and gain • Filters to attenuate harmonic output of signal sources, if harmonic measurements are desired Connections and Setup This section provides a step-by-step guide to testing the basic functionality of the EV kit. As a general pre- caution to prevent damaging the outputs by driving high-VSWR loads, do not turn on DC power or RF signal generators until all connections are made. Gain Setting Connect the header pins for B4–B0 to GND for maxi- mum gain (20dB typ). See Table 1 for other gain- setting configurations. To set a logic high on B4–B0, leave the respective header pin unconnected as on- board resistors pull up the logic to +5V. To control B4–B0 using external logic (voltage limits per the data sheet), ensure that +5V is applied to the chip. Failure to do so can cause the on-chip ESD diodes to draw significant current and can damage the part. Testing the Supply Current 1) Connect 50 Ω terminations to RF_IN and RF_OUT. 2) With the DC supply disabled, set it to +5.0V (through a low internal resistance ammeter, if desired) and connect to the +5V and GND terminals on the EV kit. If available, set the current limit to 400mA. 3) Enable the DC supply; the supply current should read approximately 250mA. Testing the Power Gain 1) Connect the RF signal generator to the RF_IN SMA connector. Do not turn on the generator’s output. Set the generator to an output frequency of 70MHz, and set the generator power level to -15dBm. 2) Connect the spectrum analyzer to the RF_OUT SMA connector. Set the spectrum analyzer to a center fre- quency of 70MHz and a total span of 1MHz. 3) With the DC supply disabled, set it to +5.0V (through a low internal-resistance ammeter, if desired) and connect to the +5V and GND terminals on the EV kit. If available, set the current limit to 400mA. 4) Connect B4–B0 to GND for 0dB attenuation. 5) Enable the DC supply, and then activate the RF gen- erator’s output. A 70MHz signal shown on the spec- ATTENUATION (dB) B4 (16dB) B3* (8dB) B2 (4dB) B1 (2dB) B0 (1dB) 0 0 00 00 1 0 00 01 2 0 00 10 3 0 00 11 4 0 01 00 5 0 01 01 6 0 01 10 7 0 01 11 8 0 10 00 9 0 10 01 10 0 1 0 1 0 11 0 1 0 1 1 12 0 1 1 0 0 13 0 1 1 0 1 14 0 1 1 1 0 15 0 1 1 1 1 16 1X 00 0 17 1X 00 1 18 1X 01 0 19 1X 01 1 20 1X 10 0 21 1X 10 1 22 1X 11 0 23 1X 11 1 Table 1. Attenuation Setting vs. Gain- Control Bits *Enabling B4 disables B3 and the minimum attenuation is 16dB. |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |