| Electronic Components Datasheet Search |
|
TDA8735T Datasheet(PDF) 4 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
TDA8735T Datasheet(HTML) 4 Page - NXP Semiconductors |
|
4 / 16 page ![]() 1998 Oct 23 4 Philips Semiconductors Product specification PLL frequency synthesizer TDA8735 PINNING SYMBOL PIN DESCRIPTION XTAL1 1 reference oscillator output XTAL2 2 reference oscillator input VCC1 3 supply voltage 1 VEE 4 ground n.c. 5 not connected DEC 6 prescaler decoupling VCOFI 7 VCO input frequency BS 8 band switch output n.c. 9 not connected SDA 10 serial data input (I2C-bus) SCL 11 serial clock input (I2C-bus) AS 12 address select input (I2C-bus) n.c. 13 not connected LOOPI 14 tuning voltage amplifier input LOOPO 15 external loop filter output VCC2 16 supply voltage 2 Fig.2 Pin configuration. handbook, halfpage TDA8735 MGH650 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 XTAL1 XTAL2 VCC1 VEE n.c. DEC VCOFI BS n.c. SDA SCL AS n.c. LOOPI LOOPO VCC2 FUNCTIONAL DESCRIPTION The TDA8735 contains the following parts and facilities: • Input amplifier VCO signal • A prescaler with the divisors 3 : 4 and a 2-bit programmable swallow counter • A 13-bit programmable counter • A digital memory phase detector • A reference frequency channel comprised of a 4 MHz crystal oscillator followed by a reference counter; the reference frequency can be 1, 10 or 25 kHz and is applied to the digital memory phase detector • An I2C-bus interface with data latches and control logic; the I2C-bus is intended for communication between microcontrollers and different ICs or modules. Detailed information on the I2C-bus specification is available on request. • A software-controlled switch output • A programmable current amplifier (charge pump) which consists of a 5 and a 500 µA current source, this allows adjustment of loop gain, thus providing high-current high-speed tuning and low current-stable tuning. The output at the loop amplifier can deliver a tuning voltage of up to 10.5 V (VCC2 − 1.5 V). Controls The TDA8735 is controlled via the 2-wire I2C-bus. As slave receiver for programming there is one module address, a logic 0 (R/W bit), a subaddress byte and four data bytes. The subaddress determines which one of the four data bytes is transmitted first. The module address contains a programmable address bit (D1) which with address select input AS (pin 12) makes it possible to operate two TDA8735 in one system. The auto increment facility of the I2C-bus allows programming of the TDA8735 within one transmission (address + subaddress + 4 data bytes). The TDA8735 can also be partially programmed. Transmission must then be ended by a stop condition. The bit organization of the 4 data bytes is illustrated in Fig.3 and is described below. The divider number is defined by 15-bit words, bits S0 to S14. To calculate the lock frequency, the divider number has to be multiplied by the selected reference frequency. |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |