Electronic Components Datasheet Search
  English  ▼

X  

HDSP-2113 Datasheet(PDF) 13 Page - AVAGO TECHNOLOGIES LIMITED

Part # HDSP-2113
Description  Eight Character 5 mm and 7 mm Smart Alphanumeric Displays
PDF  16 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AVAGO [AVAGO TECHNOLOGIES LIMITED]
Direct Link  http://www.avagotech.com
Logo AVAGO - AVAGO TECHNOLOGIES LIMITED

HDSP-2113 Datasheet(HTML) 13 Page - AVAGO TECHNOLOGIES LIMITED

Back Button HDSP-2113 Datasheet HTML 8Page - AVAGO TECHNOLOGIES LIMITED HDSP-2113 Datasheet HTML 9Page - AVAGO TECHNOLOGIES LIMITED HDSP-2113 Datasheet HTML 10Page - AVAGO TECHNOLOGIES LIMITED HDSP-2113 Datasheet HTML 11Page - AVAGO TECHNOLOGIES LIMITED HDSP-2113 Datasheet HTML 12Page - AVAGO TECHNOLOGIES LIMITED HDSP-2113 Datasheet HTML 13Page - AVAGO TECHNOLOGIES LIMITED HDSP-2113 Datasheet HTML 14Page - AVAGO TECHNOLOGIES LIMITED HDSP-2113 Datasheet HTML 15Page - AVAGO TECHNOLOGIES LIMITED HDSP-2113 Datasheet HTML 16Page - AVAGO TECHNOLOGIES LIMITED  
Zoom Inzoom in Zoom Outzoom out
 13 / 16 page
background image
13
Figure 5. Logic levels to access the flash RAM.
Table 2. Current Requirements at Different Brightness Levels VDD = 5.0 V
%
Current at 25°C
Symbol
D2
D1
D0
Brightness
Typ.
Units
IDD (V)
0
0
0
100
200
mA
0
0
1
80
160
mA
0
1
0
53
106
mA
0
1
1
40
80
mA
1
0
0
27
54
mA
1
0
1
20
40
mA
1
1
0
13
26
mA
Figure 6. Logic levels to access the control word register
Control Word Register
Figure 6 shows how to access the Control Word Register.
This 8-bit register performs five functions: Brightness
control, Flash RAM control, Blinking, Self Test, and Clear.
Each function is independent of the others; however, all
bits are updated during each Control Word write cycle.
Brightness (Bits 0-2)
Bits 0-2 of the Control Word adjust the brightness of the
display. Bits 0-2 are interpreted as a three bit binary code
with code (000) corresponding to maximum brightness
and code (111) corresponding to a blanked display. In
addition to varying the display brightness, bits 0-2 also
vary the average value of IDD. IDD can be calculated at any
brightness level by multiplying the percent brightness
level by the value of IDD at the 100% brightness level.
These values of IDD are shown in Table 2.
Flash Function (Bit 3)
Bit 3 determines whether the flashing character attribute
is on or off. When bit 3 is a“1,”the output of the Flash RAM
is checked. If the content of a location in the Flash RAM is
a “1,”the associated digit will flash at approximately 2 Hz.
For an external clock, the blink rate can be calculated by
driving the clock frequency by 28,672. If the flash enable
bit of the Control Word is a “0,” the content of the Flash
RAM is ignored. To use this function with multiple display
systems, see the Display Reset section.
Blink Function (Bit 4)
Bit 4 of the Control Word is used to synchronize blinking
of all eight digits of the display. When this bit is a “1” all
eight digits of the display will blink at approximately 2
Hz. The actual rate is dependent on the clock frequency.
For an external clock, the blink rate can be calculated by
dividing the clock frequency by 28,672. This function will
override the Flash function when it is active. To use this
function with multiple display systems, see the Display
Reset section.
CE
FL
A4
A3
A2
A1
A0
RST
WR
RD
0
1
0
0
0
1
1
X
X
0
0
1
1
UNDEFINED
REMOVE FLASH AT
SPECIFIED DIGIT LOCATION
STORE FLASH AT
SPECIFIED DIGIT LOCATION
CONTROL SIGNALS
FLASH RAM ADDRESS
FLASH RAM DATA FORMAT
0 = LOGIC 0; 1 = LOGIC 1; X = DO NOT CARE
WRITE TO DISPLAY
READ FROM DISPLAY
UNDEFINED
D7
D6
D5
D4
D3
D2
D1
D0
X
X
X
X
X
X
X
0
1
CHARACTER
ADDRESS
000 = LEFT MOST
111 = RIGHT MOST
CE
FL
A4
A3
A2
A1
A0
RST
WR
RD
0
1
0
0
0
1
1
1
0
X
X
X
1
0
1
1
UNDEFINED
CONTROL SIGNALS
CONTROL WORD ADDRESS
CONTROL WORD DATA FORMAT
0 = LOGIC 0; 1 = LOGIC 1; X = DO NOT CARE
0 DISABLE FLASH
1 ENABLE FLASH
BRIGHTNESS
CONTROL
LEVELS
0 DISABLE BLINKING
1 ENABLE BLINKING
0 NORMAL OPERATION
1 CLEAR FLASH AND CHARACTER RAMS
0
X NORMAL OPERATION; X IS IGNORED
1
X START SELF TEST; RESULT GIVEN IN X
X = 0 FAILED
X = 1 PASSED
WRITE TO DISPLAY
READ FROM DISPLAY
UNDEFINED
D7
D6
D5
D4
D3
D2
D1
D0
C
S
S
BL
F
B
0
0
0
100%
0
0
1
80%
0
1
0
53%
0
1
1
40%
1
0
0
27%
1
0
1
20%
1
1
0
13%
1
1
1
0%
B
B



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com