Electronic Components Datasheet Search
  English  ▼

X  

RT916850GS Datasheet(PDF) 7 Page - Richtek Technology Corporation

Part # RT916850GS
Description  200mA/500mA Fixed Output Voltage LDO Regulator
PDF  11 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  RICHTEK [Richtek Technology Corporation]
Direct Link  http://www.richtek.com
Logo RICHTEK - Richtek Technology Corporation

RT916850GS Datasheet(HTML) 7 Page - Richtek Technology Corporation

Back Button RT916850GS Datasheet HTML 3Page - Richtek Technology Corporation RT916850GS Datasheet HTML 4Page - Richtek Technology Corporation RT916850GS Datasheet HTML 5Page - Richtek Technology Corporation RT916850GS Datasheet HTML 6Page - Richtek Technology Corporation RT916850GS Datasheet HTML 7Page - Richtek Technology Corporation RT916850GS Datasheet HTML 8Page - Richtek Technology Corporation RT916850GS Datasheet HTML 9Page - Richtek Technology Corporation RT916850GS Datasheet HTML 10Page - Richtek Technology Corporation RT916850GS Datasheet HTML 11Page - Richtek Technology Corporation  
Zoom Inzoom in Zoom Outzoom out
 7 / 11 page
background image
RT9168/A
7
DS9168/A-15 March 2007
www.richtek.com
Application Information
Capacitor Selection and Regulator Stability
Like any low-dropout regulator, the external capacitors used
with the RT9168/A must be carefully selected for regulator
stability and performance.
Using a capacitor whose value is > 1
μF on the
RT9168/A input and the amount of capacitance can be
increased without limit. The input capacitor must be
located not more than 0.5" from the input pin of the IC
and returned to a clean analog ground. Any good quality
ceramic or tantalum can be used for this capacitor. The
capacitor with larger value and lower ESR (equivalent
series resistance) provides better PSRR and line-
transient response.
The output capacitor must meet both requirements for
minimum amount of capacitance and ESR in all LDO
applications. The RT9168/A is designed specifically to
work with low ESR ceramic output capacitor in space-
saving and performance consideration. Using a ceramic
capacitor whose value is at least 1
μF with ESR is > 5mΩ
on the RT9168/A output ensures stability. The
RT9168/A still works well with output capacitor of other
types due to the wide stable ESR range. Figure 1 shows
the curves of allowable ESR range as a function of load
current for various output voltages and capacitor values.
Output capacitor of larger capacitance can reduce noise
and improve load-transient response, stability, and PSRR.
The output capacitor should be located not more than
0.5" from the VOUT pin of the RT9168/A and returned to a
clean analog ground.
Note that some ceramic dielectrics exhibit large
capacitance and ESR variation with temperature. It may
be necessary to use 2.2
μF or more to ensure stability at
temperatures below -10
°C in this case. Also, tantalum
capacitors, 2.2
μF or more may be needed to maintain
capacitance and ESR in the stable region for strict
application environment.
Tantalum capacitors maybe suffer failure due to surge
current when it is connected to a low-impedance source
of power (like a battery or very large capacitor). If a
tantalum capacitor is used at the input, it must be
guaranteed to have a surge current rating sufficient for
the application by the manufacture.
Load-Transient Considerations
The RT9168/A load-transient response graphs (see Typical
Operating Characteristics) show two components of the
output response: a DC shift from the output impedance
due to the load current change, and the transient response.
The DC shift is quite small due to the excellent load
regulation of the IC. Typical output voltage transient spike
for a step change in the load current from 0mA to 50mA is
tens mV, depending on the ESR of the output capacitor.
Increasing the output capacitor's value and decreasing the
ESR attenuates the overshoot.
Shutdown Input Operation
The RT9168/A is shutdown by pulling the EN input low,
and turned on by driving the input high. If this feature is
not to be used, the EN input should be tied to VIN to
keep the regulator on at all times (the EN input must not
be left floating).
Figure 1
Region of Stable Cout ESR v.s Load Current
0.001
0.01
0.1
1
10
100
0
40
80
120
160
200
Load Current (mA)
COUT = 4.7uF
COUT = 1uF
Unstable Region
Stable Region
Unstable Region



Html Pages

1 2 3 4 5 6 7 8 9 10 11


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com