Electronic Components Datasheet Search
  English  ▼

X  

DAC7731EB Datasheet(PDF) 11 Page - Texas Instruments

Part # DAC7731EB
Description  16-Bit, Voltage Output, Serial Input DIGITAL-TO-ANALOG CONVERTER
PDF  23 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  TI2 [Texas Instruments]
Direct Link  https://www.ti.com
Logo TI2 - Texas Instruments

DAC7731EB Datasheet(HTML) 11 Page - Texas Instruments

Back Button DAC7731EB Datasheet HTML 7Page - Texas Instruments DAC7731EB Datasheet HTML 8Page - Texas Instruments DAC7731EB Datasheet HTML 9Page - Texas Instruments DAC7731EB Datasheet HTML 10Page - Texas Instruments DAC7731EB Datasheet HTML 11Page - Texas Instruments DAC7731EB Datasheet HTML 12Page - Texas Instruments DAC7731EB Datasheet HTML 13Page - Texas Instruments DAC7731EB Datasheet HTML 14Page - Texas Instruments DAC7731EB Datasheet HTML 15Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 11 / 23 page
background image
DAC7731
11
SBAS249B
www.ti.com
V
CC
REF
OUT
REF
IN
REFADJ
V
REF
R
OFFSET
AGND
RFB2
RFB1
SJ
V
OUT
V
DD
V
SS
REFEN
RSTSEL
SCLK
CS
SDO
SDI
LDAC
RST
NC
TEST
DGND
1
2
3
4
5
6
7
8
9
10
11
12
24
23
22
21
20
19
18
17
16
15
14
13
DAC7731
1
µF
0.1
µF
V
CC
1
µF
0.1
µF
V
DD
Control/Data
Bus
1
µF0.1µF
V
SS
(–10V to +10V)
FIGURE 4. Basic Operation: VOUT = –10V to +10V.
ANALOG OUTPUTS
The output amplifier can swing to within 1.4V of the supply
rails, specified over the –40
°C to +85°C temperature range.
This allows for a
±10V DAC voltage output operation from
±12V supplies with a typical 5% tolerance.
When the DAC7731 is configured for a unipolar, 0V to 10V
output, a negative voltage supply is required. This is due to
internal biasing of the output stage. Please refer to the
Electrical Characteristics table (see page 3) for more infor-
mation.
The minimum and maximum voltage output values are de-
pendent upon the output configuration implemented and
reference voltage applied to the DAC7731. Please note that
VSS (the negative power supply) must be in the range of
–4.75V to –15.75V for unipolar operation. The voltage on VSS
sets several bias points within the converter and is required
in all modes of operation. If VSS is not in one of these two
configurations, the bias values may be in error and proper
operation of the device is not ensured.
Supply sequence is important in establishing the correct
startup of the DAC. The following supply sequence must be
followed: VSS (device substrate) first, then VDD followed by
VCC. In addition, each supply must reach the values specified
in the Electrical Characteristics table (see page 3) within
100ms of its ramp start.
REFERENCE INPUTS
The DAC7731 provides a built-in +10V voltage reference and
on-chip buffer to allow external component reference drive. To
use the internal reference, REFEN must be LOW, enabling the
reference circuitry of the DAC7731 (as shown in Table I) and
the REFOUT pin must be connected to REFIN. This is the input
to the on-chip reference buffer. The buffer output is provided
at the VREF pin. In this configuration, VREF is used to setup the
REFEN
ACTION
1
Internal Reference disabled;
REFOUT = High Impedance
0
Internal Reference enabled;
REFOUT = +10V
TABLE I. REFEN Action.
The internal reference of the DAC7731 can be disabled when
use of an external reference is desired. When using an
external reference, the reference input, REFIN, can be any
voltage between 4.75V (or VSS + 14V, whichever is greater)
and VCC – 1.4V.
DIGITAL INTERFACE
Table II shows the input data format for the DAC7731 and
Table III illustrates the basic control logic of the device. The
serial interface consists of a chip select input (CS), serial data
clock input (SCLK), serial data input (SDI), serial data output
(SDO), and load control input (LDAC). An asynchronous reset
input (RST), which is active LOW, is provided to simplify start-
up conditions, periodic resets, or emergency resets to a known
state, depending on the status of the reset select (RSTSEL)
signal. Please refer to the
DAC Reset section for additional
information regarding the reset operation.
CONTROL STATUS
COMMAND
CS RST RSTSEL LDAC SCLK
ACTION
H
H
X
X
X
Shift Register is disabled on the serial bus.
Enable SDO pin from High Impedance;
L
H
X
X
X
enables shift operation and I/O bus
(SCLK, SDI, SDO).
LH
X
X
↑
Serial Data Shifted into Input Register
↑
H
X
X
L
Serial Data Shifted into Input Register(1)
XH
X
↑
X
Data in Input Register is Loaded into DAC Register.
X
L
H
X
X
Resets Input and DAC Registers to mid-scale.
X
L
L
X
X
Resets Input and DAC Registers to min-scale.
NOTE: (1) In order to avoid unwanted shifting of the input register by an
additional bit, care must be taken that a rising edge on CS only occurs
when SCLK is HIGH.
TABLE III. DAC7731 Logic Truth Table.
ANALOG OUTPUT
TABLE II. DAC7731 Data Format.
DIGITAL INPUT
Unipolar Configuration
Bipolar Configuration
Unipolar Straight Binary
Bipolar Offset Binary
0x0000
Zero (0V)
–Full-Scale (–VREF or –VREF/2)
0x0001
Zero + 1LSB
–Full-Scale + 1LSB
::
:
0x8000
1/2 Full-Scale
Bipolar Zero
0x8001
1/2 Full-Scale + 1LSB
Bipolar Zero + 1LSB
::
:
0xFFFF
Full-Scale (VREF – 1LSB)
+Full-Scale (+VREF – 1LSB
or +VREF/2 – 1LSB)
DAC7731 output amplifier into one of three voltage output
modes as discussed earlier. VREF can also be used to drive
other system components requiring an external reference.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com