Electronic Components Datasheet Search
  English  ▼

X  

PCM1804 Datasheet(PDF) 28 Page - Texas Instruments

Part # PCM1804
Description  FULL DIFFERENTIAL ANALOG INPUT 24-BIT, 192-kHz STEREO A/D CONVERTER
PDF  38 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  TI2 [Texas Instruments]
Direct Link  https://www.ti.com
Logo TI2 - Texas Instruments

PCM1804 Datasheet(HTML) 28 Page - Texas Instruments

Back Button PCM1804 Datasheet HTML 24Page - Texas Instruments PCM1804 Datasheet HTML 25Page - Texas Instruments PCM1804 Datasheet HTML 26Page - Texas Instruments PCM1804 Datasheet HTML 27Page - Texas Instruments PCM1804 Datasheet HTML 28Page - Texas Instruments PCM1804 Datasheet HTML 29Page - Texas Instruments PCM1804 Datasheet HTML 30Page - Texas Instruments PCM1804 Datasheet HTML 31Page - Texas Instruments PCM1804 Datasheet HTML 32Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 28 / 38 page
background image
PCM1804-Q1
SLES271A – JUNE 2012 – REVISED AUGUST 2012
www.ti.com
APPLICATION INFORMATION
BOARD DESIGN AND LAYOUT CONSIDERATIONS
VCC and VDD Pins
The digital and analog power supply lines to the PCM1804-Q1 device should be bypassed to the corresponding
ground pins with 0.1-
μF ceramic and 10-μF tantalum capacitors placed as close to the pins as possible to
maximize the dynamic performance of the ADC. Although the PCM1804-Q1 device has two power lines to
maximize the potential of dynamic performance, using one common power supply is recommended to avoid
unexpected power-supply trouble like latch-up or the power-supply sequence.
VIN Pins
Using 0.01-
μF film capacitors between the left-channel analog input positive pin and left-channel analog input
negative pin, and between right-channel analog input positive pin and right-channel analog input negative pin is
strongly recommended to remove higher-frequency noise from the delta-sigma input section.
VREFX and VCOMX Inputs
Use 0.1-
μF ceramic and 10-μF tantalum capacitors between the left-channel voltage reference output, right-
channel voltage reference output, and corresponding analog ground pins, to ensure low source impedance at
ADC references. Use 0.1-
μF tantalum capacitors between left-channel analog common-mode voltage, right-
channel analog common-mode voltage and corresponding analog ground pins to ensure low source impedance
of common voltage. These capacitors should be located as close as possible to the left-channel voltage
reference output, right-channel voltage reference output, left-channel analog common-mode voltage, and right-
channel analog common-mode voltage pins to reduce dynamic errors on references and common voltage. The
DC voltage level of these pins is 2.5 V.
DATA/DSDR, BCK/DSDL, and LRCK/DSDBCK Pins
The DATA/DSDR, BCK/DSDL, and LRCK/DSDBCK pins in master mode have large load drive capability.
Locating the buffer near the PCM1804-Q1 device and minimizing the load capacitance, minimizes the digital-
analog crosstalk and maximizes the dynamic performance of the ADC.
System Clock
The quality of the system clock can influence dynamic performance because the PCM1804-Q1 device operates
based on a system clock. Therefore, it might be necessary to consider the system clock duty, jitter, and the time
difference between system clock transition and BCK/DSDL or LRCK/DSDBCK transition in slave mode.
Reset Control
If capacitors larger than 10
μF are used on left-channel voltage reference output and right-channel voltage
reference output, an external reset control with a delay time corresponding to the left-channel voltage reference
output and right-channel voltage reference output response is required. Also, it works as a power-down control.
APPLICATION CIRCUIT FOR SINGLE-ENDED INPUT
An application diagram for a single-ended input circuit is shown in Figure 44. The maximum signal input voltage
and differential gain of this circuit is designed as Vin(max) = 8.28 Vpp, Ad = 0.3. Differential gain (Ad) is given by R3
/ R1(R4 / R2) in a circuit configured as a normal inverted-gain amplifier. Resistor R5 (R6) in the feedback loop
gives low-impedance drive operation and noise filtering for the analog input of the PCM1804-Q1 device. The
circuit technique using R5 (R6) is recommended.
28
Copyright © 2012, Texas Instruments Incorporated



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com