High reliability

, Low ESR, High ripple current.

Long life of 8000 hours at 125°C.

SMD type : Lead free reflow soldering

　condition at 260°C peak complete correspondence.

Compliant to the RoHS directive (2011/65/EU,(EU)2015/863).

ESR after Endurance at -40°C.

AEC-Q200 Qualified. Please contact us for details.

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

PCMChipType,HigherCapacitance

High Temperature Range

Performance Characteristics

–55 to +125°C

Category Temperature Range

Item

Specifications

Temperature Characteristics

(Max.Impedance Ratio)

Rated Voltage Range

Rated Capacitance Range

Capacitance Tolerance

Tangent of loss angle (tan δ)

ESR ( 1)

Leakage Current ( 2)

16 to 80V

12 to 1000µF

± 20% at 120Hz, 20°C

Less than or equal to the specified value at 120Hz, 20°C

Less than or equal to the specified value at 100kHz, 20°C

After 2 minutes' application of rated voltage, leakage current is not more than 0.03CV.

Damp Heat

(Steady State)

Resistance to

Soldering Heat

Marking

The specifications listed at right shall be met when the

capacitors are restored to 20°C after the rated voltage is

applied for 8000 hours (φD = 6.3:6000hours) at 125°C.

The specifications listed at right shall be met when the

capacitors are restored to 20°C after the rated voltage is

applied for 2000 hours at 85°C, 85% RH.

After soldering the capacitor under the soldering conditions prescribed

here, the capacitor shall meet the specifications listed at right.

Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.

The duration for over +230°C temperature at capacitor surface shall not

exceed 60 seconds.

In case peak temperature is 260°C or less, reflow soldering shall be two

times maximum.

Measurement for solder temperature profile shall be made at the

capacitor top.

Navy blue print on the case top

Capacitance change

tan δ

Leakage current ( 2)

ESR ( 1)

Within ± 20% of initial capacitance value ( 3)

150% or less of the initial specified value

200% or less of the initial specified value

Less than or equal to the initial specified value

Capacitance change

tan δ

Leakage current ( 2)

ESR ( 1)

Within ± 20% of initial capacitance value ( 3)

150% or less of the initial specified value

200% or less of the initial specified value

Less than or equal to the initial specified value

Capacitance change

tan δ

Leakage current ( 2)

ESR ( 1)

Within ± 10% of the initial capacitance value ( 3)

130% or less than the initial specified value

130% or less than the initial specified value

Less than or equal to the initial specified value

Endurance

Z(+125°C) / Z(+20°C)

1.25

(100kHz)

Z(

–55°C) / Z(+20°C)

1.25

1 ESR should be measured at both of the terminal ends closest where the terminals

protrude through the plastic platform.

2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of

applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C.

3 Initial value : The value before test of examination of resistance to soldering.

φ6.3: L±0.3

φ8,10: L ±0.5

H

0.3 max.

C±0.2

Series

Voltage (V:35V)

Plastic platform

Lot No.

Capacitance

Negative

Positive

Negative

Positive

Vibration Resistance

H

0.3 max.

C±0.2

L±0.5

Plastic platform

Aid electrode

Series

Voltage (V:35V)

Lot No.

Capacitance

Standard

Dimensions

P

1

C

2

M

3

1

4

V

5

1

6

5

7

1

8

M

9

C

10

L

11

1

12

G

13

S

14

Configuration

Taping code

Size code

Capacitance tolerance (±20%)

Rated capacitance (150µF)

Rated voltage (35V)

Series name

Type

Standard

Vibration

Resistance

Code

Size

L

※Please ask for

Part Number.

Type numbering system (Example : 35V 150µF)

φ6.3×8L(φ6.3×8L),φ8×10L(φ8×10.5L),φ10×10L(φ10×10.5L),φ10×12.7L(φ10×13.2L) :

The vibration structure-resistant product is also available upon request, please ask for details.

( ) : Size of the vibration structure-resistant product.

Dimension table in next page.

Less than or equal to the specified value at 100kHz, -40°C

ESR after Endurance ( 1)

After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4

clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.

Shelf Life

PCM LongLifeAssurance PCR

※ I : Leakage Current (µA), C : Rated Capacitance (µF), V : Rated Voltage (V)

φD

L

A

B

C

E

H

Size

8.0

6.9

9.0

8.3

8.3

3.2

0.8 to 1.1

φ8×7L

8.0

9.9

9.0

8.3

8.3

3.2

0.8 to 1.1

φ8×10L

8.0

11.9

9.0

8.3

8.3

3.2

0.8 to 1.1

φ8×12L

10.0

7.9

11.0

10.3

10.3

4.6

0.8 to 1.1

φ10×8L

6.3

7.9

7.3

6.6

6.6

2.1

0.5 to 0.8

φ6.3×8L

6.3

5.9

7.3

6.6

6.6

2.1

0.5 to 0.8

φ6.3×6L

10.0

9.9

11.0

10.3

10.3

4.6

0.8 to 1.1

φ10×10L

10.0

12.6

11.0

10.3

10.3

4.6

0.8 to 1.1

φ10×12.7L

(mm)

Code C

V

16

D

20

E

25

V

35

H

50

J

63

Voltage

K

80

(mm)

Standard

Size

φD

L

A

B

C

E

H

φ8

×7L

8.0

6.9

9.0

8.3

8.3

3.2

0.8 to 1.1

φ6.3

×6L

6.3

5.9

7.3

6.6

6.6

2.1

0.5 to 0.8

φ8

×10L

8.0

9.9

9.0

8.3

8.3

3.2

0.8 to 1.1

φ6.3

×8L

6.3

7.9

7.3

6.6

6.6

2.1

0.5 to 0.8

φ8

×12L

8.0

11.9

9.0

8.3

8.3

3.2

0.8 to 1.1

φ10

×8L

10.0

7.9

11.0

10.3

10.3

4.6

0.8 to 1.1

φ10

×10L

10.0

9.9

11.0

10.3

10.3

4.6

0.8 to 1.1

φ10

×12.7L

10.0

12.6

11.0

10.3

10.3

4.6

0.8 to 1.1

Size

φD

L

A

B

C

E

H

φ6.3×8L

6.3

7.5

7.3

6.6

6.6

2.5

0.5 to 0.8

φ8×10.5L

8.0

10.0

9.0

8.3

8.3

3.1

1.1 to 1.5

φ10×10.5L

10.0

10.0

11.0

10.3

10.3

4.6

1.1 to 1.5

φ10×13.2L

10.0

12.7

11.0

10.3

10.3

4.6

1.1 to 1.5

(mm)

Vibration Resistance

Frequency coefficient of rated ripple current

Frequency

Coefficient

120Hz 1kHz 10kHz 100kHz or more

0.05 0.30 0.70

1.00

CAT.8100N