MP1541 – 1.3MHz BOOST CONVERTER

MP1541 Rev.1.5

www.MonolithicPower.com

7

9/5/2017

MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.

© 2017 MPS. All Rights Reserved.

APPLICATIONS INFORMATION

COMPONENT SELECTION

Setting the Output Voltage

Set the output voltage by selecting the resistive

voltage divider ratio. Use 11.8kΩ for the low-

side resistor R2 of the voltage divider.

Determine the high-side resistor R1 by the

equation:



FB

FB

OUT

V

V

-

V

2

R

1

R



where VOUT is the output voltage.

For R2 = 11.8kΩ and VFB = 1.25V, then

R1 (kΩ) = 9.44kΩ (VOUT – 1.25V).

Selecting the Input Capacitor

An input capacitor is required to supply the AC

ripple current to the inductor, while limiting noise

at the input source. This capacitor must have low

ESR, so ceramic is the best choice.

Use an input capacitor value of 4.7μF or greater.

This capacitor must be placed physically close

to the IN pin. Since it reduces the voltage ripple

seen at IN, it also reduces the amount of EMI

passed back along that line to the other circuitry.

Selecting the Output Capacitor

A single 4.7

F to 10F ceramic capacitor

usually provides sufficient output capacitance

for most applications. If larger amounts of

capacitance is desired for improved line support

and transient response, tantalum capacitors

can be used in parallel with the ceramic. The

impedance of the ceramic capacitor at the

switching frequency is dominated by the

capacitance, and so the output voltage ripple is

mostly independent of the ESR. The output

voltage ripple VRIPPLE is calculated as:





SW

UT

O

IN

UT

O

LOAD

RIPPLE

f

2

C

V

V

V

I

V









Where VIN is the input voltage, ILOAD is the load

current, C2 is the capacitance of the output

capacitor, and fSW is the 1.3MHz switching

frequency.

Selecting the Inductor

The inductor is required to force the output

voltage higher while being driven by the lower

input voltage. Choose an inductor that does not

saturate at the SW current limit. A good rule for

determining the inductance is to allow the peak-

to-peak ripple current to be approximately 30%-

50% of the maximum input current. Make sure

that the peak inductor current is below 75% of

the typical current limit at the duty cycle used to

prevent loss of regulation due to the current

limit variation.

Calculate the required inductance value L using

the equations:

I

f

V

)

V

-

(V

V

L

SW

OUT

IN

OUT

IN

















IN

)

MAX

(

LOAD

OUT

)

MAX

(

IN

V

I

V

I





)

MAX

(

IN

I

%

50

%

30

I







Where ILOAD(MAX) is the maximum load current, ∆I

is the peak-to-peak inductor ripple current, and η

is efficiency. For the MP1541, 4.7µH is

recommended for input voltages less than 3.3V

and 10µH for inputs greater than 3.3V.

Selecting the Diode

The output rectifier diode supplies current to the

inductor when the internal MOSFET is off. To

reduce losses due to diode forward voltage and

recovery time, use a Schottky diode. Choose a

diode whose maximum reverse voltage rating is

greater than the maximum output voltage. For

output voltage less than 20V, it is recommended

to choose the MBR0520 for most applications.

This diode is used for load currents less than

500mA. If the average current is more than

500mA the Microsemi UPS5817 is a good choice.