| Electronic Components Datasheet Search |
|
TAS2505IRGET Datasheet(PDF) 6 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
TAS2505IRGET Datasheet(HTML) 6 Page - Texas Instruments |
|
6 / 36 page ![]() At 25°C, AVDD = 1.8V, IOVDD = 1.8V, SPKVDD = 3.6V, DVDD = 1.8V, fS (audio) = 48kHz, CODEC_CLKIN = 256 × fS, PLL = Off PARAMETER TEST CONDITIONS MIN TYP MAX UNIT PO Maximum output power SPKVDD = 3.6V, BTL measurement, CM = 0.9V, class-D gain = 18dB, THD = 10% 0.7 W SPKVDD = 4.2V, BTL measurement, CM = 0.9V, class-D gain = 18dB, THD = 10% 1 SPKVDD = 5.5V, BTL measurement, CM = 0.9V, class-D gain = 18dB, THD = 10% 1.7 SPKVDD = 3.6V, BTL measurement, CM = 0.9V, class-D gain = 18dB, THD = 1% 0.5 SPKVDD = 4.2V, BTL measurement, CM = 0.9V, class-D gain = 18dB, THD = 1% 0.8 SPKVDD = 5.5V, BTL measurement, CM = 0.9V, class-D gain = 18dB, THD = 1% 1.3 ANALOG BYPASS TO CLASS-D SPEAKER AMPLIFIER Device setup BTL measurement, driver gain = 6dB, load = 4Ω (differential), 50pF, input signal frequency fi = 1KHz Voltage gain Input common-mode = 0.9V 4 V/V Gain error –1dBFS (446mVrms), 1kHz input signal ±0.7 dB ICN Idle channel noise Idle channel, IN1L and IN1R ac-shorted to ground, measured as idle-channel noise, A-weighted(2) (1) 32.6 μVms THD+N Total harmonic distortion + noise –1dBFS (446mVrms), 1kHz input signal –73.7 dB SHUTDOWN POWER CONSUMPTION Device setup Power down POR, /RST held low, AVDD = 1.8V, IOVDD = 1.8V, SPKVDD = 4.2V, DVDD = 1.8V I(AVDD) 1.32 µA I(DVDD) 0.04 µA I(IOVDD) 0.68 µA I(SPKVDD) 2.24 µA DIGITAL INPUT/OUTPUT Logic family CMOS VIH Logic level IIH = 5μA, IOVDD ≥ 1.6V 0.7 × IOVDD V IIH = 5μA, IOVDD < 1.6V IOVDD VIL IIL = 5μA, IOVDD ≥ 1.6V –0.3 0.3 × IOVDD V IIL = 5μA, IOVDD < 1.6V 0 VOH IOH = 2 TTL loads 0.8 × IOVDD V VOL IOL = 2 TTL loads 0.25 V Capacitive load 10 pF (1) All performance measurements were done with a 20kHz low-pass filter and, where noted, an A-weighted filter. Failure to use such a filter may result in higher THD+N and lower SNR and dynamic range readings than shown in the Electrical Characteristics. The low-pass filter removes out-of-band noise, which, although not audible, may affect dynamic specification values. (2) Ratio of output level with 1kHz full-scale sine-wave input, to the output level with the inputs short-circuited, measured A-weighted over a 20Hz to 20kHz bandwidth using an audio analyzer. 5.6 I2S/LJF/RJF Timing in Master Mode All specifications at 25°C, DVDD = 1.8V(1) PARAMETER IOVDD = 1.8V IOVDD = 3.3V UNIT MIN MAX MIN MAX td(WS) WCLK delay 45 45 ns TAS2505 SLAS778D – FEBRUARY 2013 – REVISED JANUARY 2025 www.ti.com 6 Submit Document Feedback Copyright © 2025 Texas Instruments Incorporated Product Folder Links: TAS2505 |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |