Electronic Components Datasheet Search
  English  ▼

X  

PLDC20RA10 Datasheet(PDF) 2 Page - Cypress Semiconductor

Part # PLDC20RA10
Description  Reprogrammable Asynchronous CMOS Logic Device
PDF  14 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  CYPRESS [Cypress Semiconductor]
Direct Link  http://www.cypress.com
Logo CYPRESS - Cypress Semiconductor

PLDC20RA10 Datasheet(HTML) 2 Page - Cypress Semiconductor

  PLDC20RA10 Datasheet HTML 1Page - Cypress Semiconductor PLDC20RA10 Datasheet HTML 2Page - Cypress Semiconductor PLDC20RA10 Datasheet HTML 3Page - Cypress Semiconductor PLDC20RA10 Datasheet HTML 4Page - Cypress Semiconductor PLDC20RA10 Datasheet HTML 5Page - Cypress Semiconductor PLDC20RA10 Datasheet HTML 6Page - Cypress Semiconductor PLDC20RA10 Datasheet HTML 7Page - Cypress Semiconductor PLDC20RA10 Datasheet HTML 8Page - Cypress Semiconductor PLDC20RA10 Datasheet HTML 9Page - Cypress Semiconductor Next Button
Zoom Inzoom in Zoom Outzoom out
 2 / 14 page
background image
PLDC20RA10
Document #: 38-03012 Rev. **
Page 2 of 14
Macrocell Architecture
Figure 1 illustrates the architecture of the 20RA10 macrocell.
The cell dedicates three product terms for fully asynchronous
control of the register set, reset, and clock functions, as well
as, one term for control of the output enable function.
The output enable product term output is ANDed with the input
from pin 13 to allow either product term or hardwired external
control of the output or a combination of control from both
sources. If product-term-only control is selected, it is automat-
ically chosen for all outputs since, for this case, the external
output enable pin must be tied LOW. The active polarity of
each output may be programmed independently for each out-
put cell and is subsequently fixed. Figure 2 illustrates the out-
put enable options available.
When an I/O cell is configured as an output, combinatorial-only
capability may be selected by forcing the set and reset product
term outputs to be HIGH under all input conditions. This is
achieved by programming all input term programming cells for
these two product terms. Figure 3 illustrates the available out-
put configuration options.
An additional four uncommitted product terms are provided in
each output macrocell as resources for creation of user-de-
fined logic functions.
Programmable I/O
Because any of the ten I/O pins may be selected as an input,
the device input configuration programmed by the user may
vary from a total of nine programmable plus ten dedicated in-
puts (a total of nineteen inputs) and one output down to a
ten-input, ten-output configuration with all ten programmable
I/O cells configured as outputs. Each input pin available in a
given configuration is available as an input to the four control
product terms and four uncommitted product terms of each
programmable I/O macrocell that has been configured as an
output.
An I/O cell is programmed as an input by tying the output en-
able pin (pin 13) HIGH or by programming the output enable
product term to provide a LOW, thereby disabling the output
buffer, for all possible input combinations.
When utilizing the I/O macrocell as an output, the input path
functions as a feedback path allowing the output signal to be
fed back as an input to the product term array. When the output
cell is configured as a registered output, this feedback path
may be used to feed back the current output state to the device
inputs to provide current state control of the next output state
as required for state machine implementation.
Preload and Power-Up Reset
Functional testability of programmed devices is enhanced by
inclusion of register preload capability, which allows the state
of each register to be set by loading each register from an
external source prior to exercising the device. Testing of com-
plex state machine designs is simplified by the ability to load
an arbitrary state without cycling through long test vector se-
quences to reach the desired state. Recovery from illegal
states can be verified by loading illegal states and observing
recovery. Preload of a particular register is accomplished by
impressing the desired state on the register output pin and
lowering the signal level on the preload control pin (pin1) to a
logic LOW level. If the specified preload set-up, hold and pulse
width minimums have been observed, the desired state is
loaded into the register. To insure predictable system initializa-
tion, all registers are preset to a logic LOW state upon pow-
er-up, thereby setting the active LOW outputs to a logic HIGH.
Note:
1.
The CG7C324 is the PLDC20RA10 packaged in the JEDEC-compatible 28-pin PLCC pinout. Pin function and pin order is identical for both PLCC pinouts. The
principal difference is in the location of the “no connect” (NC) pins
Selection Guide
Generic Part
Number
tPD ns
tSU ns
tCO ns
tCC ns
Com‘l
Mil
Com’l
Mil
Com’l
Mil
Com’l
Mil
20RA10-15
15
7
15
80
20RA10-20
20
20
10
10
20
20
80
85
20RA10-25
25
15
25
85
20RA10-35
35
20
35
85
Pin Configurations
LCC
Top View
STD PLCC/HLCC
JEDEC PLCC/HLCC
Top View
Top View
5
6
7
8
9
10
11
4 3 2
282726
12131415161718
25
24
23
22
21
20
19
I/O
I/O
I/O
I/O
I/O
I/O
2
3
4
5
6
7
25
24
23
22
21
20
19
5
6
7
8
9
10
11
121314 1516 1718
4 3 2
2827 26
I/O
I/O
I/O
I/O
I/O
I/O
2
3
4
5
6
7
PLDC20RA10
PLDC20RA10
1
1
RA10–2
RA10–3RA10–4
I
I
I
I
I
I
2
3
4
5
6
7
NC
NC
25
24
23
22
21
20
19
5
6
7
8
9
10
11
121314 1516 1718
4 3 2
2827 26
I/O
I/O
I/O
I/O
I/O
I/O
2
3
4
5
6
7
PLDC20RA10
1
I3
I
I
4
5
NC
NC
I
6
NC
I
3
I
I
4
5
NC
I6
I7
NC
NC
I2
CG7C324
[1]



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com