RCL e3

www.vishay.com

Vishay Draloric

Revision: 20-Oct-2025

7

Document Number: 20046

For technical questions, contact: thickfilmchip@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Note

(1) The quoted IEC standards are also released as EN standards with the same number and identical contents

8.1

-

Short-term overload

U = 2.5 x

≤ 2 x Umax.;

whichever is the less severe;

5 s

± (2 %

R + 0.05 Ω)

8.2

-

Single pulse high

voltage overload

Severity no. 4:

U = 10 x

or

U = 2 x Umax.;

whichever is the less severe;

10 pulses 10 μs/700 μs

± (1 %

R + 0.05 Ω)

no visible damage

8.4

-

Periodic electric

overload

U =

or

U = 2 x Umax.;

whichever is the less severe;

0.1 s on; 2.5 s off;

1000 cycles

± (1 %

R + 0.05 Ω)

no visible damage

8.5

-

Electrostatic

discharge

(human body model)

IEC 61340-3-1 (1);

3 pos. + 3 neg. discharges;

ESD voltage acc. to the size

± (1 %

R + 0.05 Ω)

9.11

6 (Fc)

Vibration

Endurance by sweeping;

10 Hz to 2000 Hz;

no resonance;

amplitude

≤ 1.5 mm or

≤ 200 m/s2;

7.5 h

± (0.25 %

R + 0.05 Ω)

no visible damage

± (0.5 %

R + 0.05 Ω)

no visible damage

11.1

58 (Td)

Solderability

Solder bath method;

Sn60Pb40

non-activated flux;

(235 ± 5) °C;

(2 ± 0.2) s

Good tinning (

≥ 95 % covered)

no visible damage

Solder bath method;

Sn96.5Ag3Cu0.5

non-activated flux;

(245 ± 5) °C;

(3 ± 0.3) s

11.2

58 (Td)

Resistance to

soldering heat

Solder bath method

(260 ± 5) °C;

(10 ± 1) s

± (0.25 %

R + 0.05 Ω)

± (0.5 %

R + 0.05 Ω)

11.3

45 (XA)

Component solvent

resistance

Isopropyl alcohol;

+50 °C; method 2

No visible damage

9.7

21 (Ue3)

Shear

(adhesion)

17.7 N

No visible damage

9.8

21 (Ue1)

Substrate bending

Depth 2 mm;

3 times

± (0.25 %

R + 0.05 Ω)

no visible damage, no open circuit in bent position

12.2

-

Voltage proof

U = 1.4 x Uins; 60 s

No flashover or breakdown

12.4

-

Flammability,

needle flame test

IEC 60695-11-5 (1);

10 s

No burning after 30 s

TEST PROCEDURES AND REQUIREMENTS

EN 60115-1

CLAUSE

IEC

60068-2 (1)

TEST

METHOD

TEST

PROCEDURE

REQUIREMENTS

PERMISSIBLE CHANGE (

ΔR)

Stability for product types:

STABILITY CLASS 1

OR BETTER

STABILITY CLASS 2

OR BETTER

RCL e3

1

Ω to 2.2 MΩ

P

70 x R

P

70 x R

15 x P

70 x R