M50LPW116N datasheet(10/36 Pages) STMICROELECTRONICS

10 / 36 page

M50LPW116

10/36

The Address/Address Multiplexed (A/A Mux)

Interface

included

for

use

Flash

Programming

equipment

for

faster

factory

programming. Only a subset of the features

available to the Low Pin Count (LPC) Interface are

available; these include all the Commands but

exclude the Security features and other registers.

The following operations can be performed using

the appropriate bus cycles: Bus Read, Bus Write,

Output Disable and Reset.

When the Address/Address Multiplexed (A/A Mux)

Interface

selected

all

the

blocks

are

unprotected. It is not possible to protect any blocks

through this interface.

Bus Read. Bus Read operations are used to

output the contents of the Memory Array, the

Electronic Signature and the Status Register. A

valid Bus Read operation begins by latching the

Row Address and Column Address signals into

the memory using the Address Inputs, A0-A10,

and the Row/Column Address Select RC. Then

Write Enable (W) and Interface Reset (RP) must

be High, VIH, and Output Enable, G, Low, VIL, in

order to perform a Bus Read operation. The Data

Inputs/Outputs will output the value, see Figure

11, A/A Mux Interface Read AC Waveforms, and

Table 24, for details of when the output becomes

valid.

Bus Write. Bus Write operations write to the

Command Interface. A valid Bus Write operation

begins by latching the Row Address and Column

Address signals into the memory using the

Address Inputs, A0-A10, and the Row/Column

Address Select RC. The data should be set up on

the Data Inputs/Outputs; Output Enable, G, and

Interface Reset, RP, must be High, VIH and Write

Enable, W, must be Low, VIL. The Data Inputs/

Outputs are latched on the rising edge of Write

Enable, W. See Figure 12, and Table 25, for

details of the timing requirements.

Output Disable. The data outputs are high-im-

pedance when the Output Enable, G, is at VIH.

Reset. During Reset mode all internal circuits are

switched off, the memory is deselected and the

outputs are put in high-impedance. The memory is

in Reset mode when RP is Low, VIL. RP must be

held Low, VIL for tPLPH. If RP is goes Low, VIL,

during

Program or

Erase

operation, the

operation is aborted and the memory cells affected

no longer contain valid data; the memory can take

up to tPLRH to abort a Program or Erase operation.

COMMAND INTERFACE

All Bus Write operations to the memory are

interpreted

the

Command

Interface.

Commands consist of one or more sequential Bus

Write operations.

After power-up or a Reset operation the memory

enters Read mode.

The commands are summarized in Table 11,

Commands. Refer to Table 11 in conjunction with

the text descriptions below.

Read Memory Array Command. The Read Mem-

ory Array command returns the memory to its

Read mode where it behaves like a ROM or

EPROM. One Bus Write cycle is required to issue

the Read Memory Array command and return the

memory to Read mode. Once the command is is-

sued the memory remains in Read mode until an-

other command is issued. From Read mode Bus

Read operations will access the memory array.

While the Program/Erase Controller is executing a

Program or Erase operation the memory will not

accept the Read Memory Array command until the

operation completes.

Read Status Register Command. The Read Sta-

tus Register command is used to read the Status

the Read Status Register command. Once the

Table 8. A/A Mux Bus Operations

Table 9. Manufacturer and Device Codes

Operation

VPP

DQ7-DQ0

Bus Read

VIL

VIH

Don’t Care

Data Output

Bus Write

VIH

VIL

VIH

VCC or VPPH

Data Input

Output Disable

VIH

Don’t Care

Hi-Z

Reset

VIL or VIH

VIL

Don’t Care

Hi-Z

Operation

A20-A1

DQ7-DQ0

Manufacturer Code

VIL

VIH

VIL

20h

Device Code

VIL

VIH

VIL

VIH

30h

M50LPW116N Datasheet(PDF) 10 Page - STMicroelectronics

M50LPW116N Datasheet(HTML) 10 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

Datasheet Download

Link URL