Electronic Components Datasheet Search
  English  ▼

X  

AD8192ACPZ Datasheet(PDF) 24 Page - Analog Devices

Part # AD8192ACPZ
Description  2:1 HDMI/DVI Switch with Equalization and DDC/CEC Buffers
PDF  28 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

AD8192ACPZ Datasheet(HTML) 24 Page - Analog Devices

Back Button AD8192ACPZ Datasheet HTML 20Page - Analog Devices AD8192ACPZ Datasheet HTML 21Page - Analog Devices AD8192ACPZ Datasheet HTML 22Page - Analog Devices AD8192ACPZ Datasheet HTML 23Page - Analog Devices AD8192ACPZ Datasheet HTML 24Page - Analog Devices AD8192ACPZ Datasheet HTML 25Page - Analog Devices AD8192ACPZ Datasheet HTML 26Page - Analog Devices AD8192ACPZ Datasheet HTML 27Page - Analog Devices AD8192ACPZ Datasheet HTML 28Page - Analog Devices  
Zoom Inzoom in Zoom Outzoom out
 24 / 28 page
background image
AD8192
Rev. 0 | Page 24 of 28
the amount of parasitic trace capacitance. An example of the
board stackup is shown in Figure 34.
The AVCC/AVEE (3.3 V) and DVCC/DVEE (3.3 V) supplies
power the core of the AD8192. The VTTI/AVEE supply (3.3 V)
powers the input termination. Similarly, the VTTO/AVEE supply
(3.3 V) powers the output termination. The AMUXVCC/ DVEE
supply (3.3 V to 5 V) powers the auxiliary multiplexer core. The
VREF_COM and VREF_AB supplies determine the logic levels
on the corresponding DDC buses. For example, if the DDC_COM
bus is using 5 V I2C, then VREF_COM should be connected to
+5 V relative to DVEE. If the DDC_AB buses are using 3.3 V
I2C, then VREF_AB should be connected to +5 V relative to DVEE.
PCB DIELECTRIC
LAYER 1: SIGNAL (MICROSTRIP)
SILKSCREEN
SILKSCREEN
PCB DIELECTRIC
PCB DIELECTRIC
LAYER 2: GND (REFERENCE PLANE)
LAYER 3: PWR (REFERENCE PLANE)
LAYER 4: SIGNAL (MICROSTRIP)
W
3W
3W
REFERENCE LAYER
RELIEVED UNDERNEATH
MICROSTRIP
In a typical application, connect all pins labeled AVEE or DVEE
directly to ground. Likewise, connect all pins labeled AVCC,
DVCC, VTTI, or VTTO to 3.3 V, and tie Pin AMUXVCC to
5 V. VREF_AB and VREF_COM can be tied to either 3.3 V
or 5 V, depending on the application. The supplies can also be
powered individually, but care must be taken to ensure that
each stage of the AD8192 is powered correctly.
Power Supply Bypassing
Figure 34. Example Board Stackup
The AD8192 requires minimal supply bypassing. When
powering the supplies individually, place a 0.01 μF capacitor
between each 3.3 V supply pin (AVCC, DVCC, VTTI, and
VTTO) and ground, and place a 0.1 μF capacitor between each
additional supply pin (AMUXVCC, VREF_AB, and VREF_COM)
and ground to filter out supply noise. Generally, place bypass
capacitors near the power pins and connect them directly to the
relevant supplies (without long intervening traces). For example, to
improve the parasitic inductance of the power supply decoupling
capacitors, minimize the trace length between capacitor landing
pads and the vias.
HPD is a dc signal presented by a sink to a source to indicate
that the source EDID is available for reading. The placement of
this signal is not critical, but it should be routed as directly as
possible.
When the AD8192 is powered up, the DDC/CEC inputs of the
selected channel are actively buffered and routed to the outputs,
and the unselected auxiliary inputs are high impedance. When
the AD8192 is powered off, all DDC/CEC inputs are placed in a
high impedance state. This prevents contention on the DDC
bus, enabling a design to include an EDID in front of the AD8192.
Power Supplies
In applications where the AD8192 is powered by a single 3.3 V
supply, it is recommended to use two reference supply planes
and bypass the 3.3 V reference plane to the ground reference
plane with one 220 pF, one 1000 pF, two 0.01 μF, and one 4.7 μF
capacitors. If the AMUXVCC, VREF_AB, and VREF_COM
connections are all powered by a single 5 V supply, it is sufficient
to use a single 0.1 μF to bypass all three connections. The capa-
citors should via down directly to the supply planes and be
placed within a few centimeters of the AD8192.
The AD8192 has five separate power supplies referenced to
two separate grounds. The supply/ground pairs are
•
AVCC/AVEE
•
VTTI/AVEE
•
VTTO/AVEE
•
DVCC/DVEE
•
AMUXVCC/DVEE
•
VREF_AB/DVEE
•
VREF_COM/DVEE



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com