| Electronic Components Datasheet Search |
|
AN219 Datasheet(PDF) 3 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
AN219 Datasheet(HTML) 3 Page - Microchip Technology |
|
3 / 6 page ![]() 2000 Microchip Technology Inc. Preliminary DS00219A-page 3 AN219 Since digital potentiometers are manufactured using a standard CMOS process with no moving parts, the reaction to these environmental changes are signifi- cantly reduced. Vibration or Shock Vibration or shock can also have an effect on an appli- cation circuit by causing physical movement. All devices that are soldered on a PCB can have failures due to vibration or shock, but the moving mechanism of mechanical potentiometers may also move. A typical specification for a mechanical potentiometer would be a ±2% change due to vibrations that span from 10Hz to 2kHz. Another way of describing the effects of movement on the mechanical potentiometer is force. Typically 20Gs of force on a higher quality mechanical potentiometer would cause a maximum of ±1% resistive change. Since there are no moving parts in digital potentiome- ters, the element will remain unchanged with vibration or shock tests unless discontinuities occur in the PCB construction. Mean Time to Failure Life One type of failure that is quantified with mechanical potentiometers is the mean time to failure life of the wiper adjustment capability. A typical specification for this type of failure would be that the device could sur- vive several hundred cycles without discontinuity. A cycle is defined as changing the wiper position across full scale once. With thin film mechanical potentiome- ters, such as those constructed of cermet, a failure resulting from repeated cycles manifests itself as reduced performance. Since the wiper of the digital potentiometer is controlled by electrical switches, the resistive elements are not effected by repeated cycles. Consequently, the digital potentiometer is a more robust solution. Nominal Total Resistance The nominal total resistance of a potentiometer is the typical specified resistance (in ohms) that can be mea- sured between terminal PA and terminal PB per Figure 1. Typical values for digital potentiometers are 10k Ω, 50kΩ, and 100kΩ. Nominal resistance values below 10k Ω become difficult to implement in silicon because of the switch resistances. Values higher than 100k Ω are possible but require more silicon, which increases the cost of the device. The range of the selection of the mechanical potenti- ometer is considerably wider with values such as 10 Ω, 20 Ω, 50Ω, 100Ω, 200Ω, 500Ω, 1kΩ, 2kΩ, 5kΩ, 10kΩ, 20k Ω, 25kΩ, 50kΩ, 100kΩ, 250kΩ, 500kΩ, 1MΩ, and 2M Ω. The mechanical potentiometer might be considered attractive because of the wide range of nominal resis- tance offerings. However, the most common nominal resistance ranges used in adjustment type circuits are 1k Ω through 1MΩ. This range of potentiometers are available in both the digital and mechanical potentiom- eters. Total Resistance Tolerance The total resistance tolerance of the element between terminal PA and terminal PB varies from part to part. With digital potentiometers that variance is dependent on processing variance of the resistive material and switches. Typical digital potentiometer total resistance tolerances are between ±20% to ±30%. On the other hand, variance of the cermet material in mechanical potentiometers range from ±10 to ±25%. Although there seems to be a degree of difference between the digital potentiometer and mechanical potentiometer, the variability of the nominal resistance of both devices is considerably larger than standard 1% discrete resistors. In some applications, these toler- ance values can cause errors that are too large. For additional design help, refer to the numerous circuit ideas in Microchip’s application note, AN-691,”Optimiz- ing Digital Potentiometer Circuits to Reduce Absolute and Temperature Variations”. Temperature Coefficient Mechanical potentiometers and digital potentiometers drift with temperature. The range of typical drift specifi- cations for the total resistance of the mechanical poten- tiometer is from ±100ppm/°C to ±300ppm/°C. Typical drift versus temperature specification for the digital potentiometer is around ±800ppm/°C. With both types of potentiometers, the temperature coefficient differ- ence between the A element (resistance between PA and PW minus the wiper resistance) and B element (resistance between PB and PW minus the wiper resis- tance) is very low. The magnitude of these specifications may or may not affect the performance of the circuit. If it is found that they do, numerous circuit ideas are available in Micro- chip’s application note, AN-691,”Optimizing Digital Potentiometer Circuits to Reduce Absolute and Tem- perature Variations”. Power Rating Mechanical potentiometers can sustain more power dissipation than the digital potentiometers. It is not unusual to have a mechanical potentiometer that is capable of dissipating 0.5W @ 70 °C (usually specified for 1000 hours). However, the wiper of the mechanical potentiometer usually can only conduct up to 1mA of current. This becomes a limitation if the potentiometer is configured so that the wiper is directly connected to terminal A or terminal B. The digital potentiometer is capable of conducting power up to 0.0055W @ 70 °C. It also has a 1mA max- imum wiper current restriction. |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |