Electronic Components Datasheet Search
  English  ▼

X  

LT8301 Datasheet(PDF) 3 Page - Analog Devices

Part # LT8301
Description  Low/Full/High-Speed USB 2.0 Isolator with Isolated Power
PDF  5 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

LT8301 Datasheet(HTML) 3 Page - Analog Devices

  LT8301 Datasheet HTML 1Page - Analog Devices LT8301 Datasheet HTML 2Page - Analog Devices LT8301 Datasheet HTML 3Page - Analog Devices LT8301 Datasheet HTML 4Page - Analog Devices LT8301 Datasheet HTML 5Page - Analog Devices  
Zoom Inzoom in Zoom Outzoom out
 3 / 5 page
background image
Circuit Note
CN-0550
analog.com
Rev. 0 | 3 of 5
of 30 V. A 150 μF capacitor is used to reduce the ripple of the
output voltage. This combination of components allows the design
to meet the standard 100 mA maximum load current drawn by
low-power USB 2.0 devices using the available 5 V bus power on
the host side.
Additionally, this circuit is capable of supporting the 500 mA max-
imum load current drawn by high-power USB 2.0 devices when
connected to an external power supply of at least 8 V. Higher load
currents can be achieved with more input voltage, up to 1.3 A at the
maximum input voltage of 32 V. For the general design procedure in
selecting these components, refer to the LT8301 data sheet.
Note that while the ADuM3165 has an insulation voltage rating of
3.75 kV rms and the LT8301 has a maximum input voltage of 42
V, these parameters will be limited by the transformer specifications
in this application. The flyback transformer used in the CN0550 is
tested at 1.5 kV rms insulation, but is only designed to comply with
IEC61558-2-16 basic insulation for a primary circuit at a working
voltage of 50 V rms. This transformer is suitable for isolation in
most laboratory test and measurement applications.
The output voltage of the LT8301 is set by an external feedback
resistor connected between the SW and RFB pins; the value of
which is calculated using Equation 1:
RFB=NPS×VOUT+VF
100×10−6
(1)
where:
RFB is the required feedback resistance in Ω.
NPS is the transformer effective primary-to-secondary turns ratio.
VOUT is the output voltage.
VF is the output diode forward voltage.
For the required output voltage of 5 V, a 3:1 transformer turns ratio,
and an output diode forward voltage of 0.3 V, Equation 1 results
in an RFB value of 159 kΩ; the closest standard 1% value to this
is 158 kΩ is considered. In practice, however, the unique sampling
scheme used by the LT8301 can introduce errors in the output
voltage. Equation 2 can be used to adjust the feedback resistance
based on the actual output voltage.
RFBFINAL = VOUTVOUTMEAS ×RFB
(2)
where:
RFB(FINAL) is the adjusted feedback resistance in Ω.
VOUT(MEAS) is the actual output voltage measured in V.
With a target VOUT of 5.0 V, a measured VOUT of 5.26 V and an
initial RFB of 158 kΩ, Equation 2 results in a resistance value of
150.19 kΩ. In CN0550, a 150 kΩ ±1% feedback resistor is used.
The resulting load regulation using these values are shown in
Figure 6.
Figure 6. Output Load Regulation Plot
COMMON VARIATIONS
Certain applications may require devices to be synchronized to a
single timing source. In these cases, directly apply a precision 24
MHz clock signal from the system microprocessor to the external
clock input of the ADuM3165 instead of using an external crystal.
If the system microprocessor and the clock signal is located on the
peripheral side rather than the host side, the ADuM3166 may be
used as an alternative. This device has the same specifications and
pinout as the ADuM3165, with the placement of the XI and XO pins
as the only difference.
The ADuM3165 VBUS1, VBUS2 operating voltage range is 3.0 V to
5.5 V, overlapping the VDD1, 2 operating range of 3.0 V to 3.6 V. If
a 3.0 V to 3.6 V supply is available on either side, the VDDx pin can
be tied to its corresponding VBUSx and powered directly. This also
reduces the overall device dissipation and extends the operating
temperature range. Refer to the ADuM3165 data sheet for more
details.
The isolation voltage rating of the CN0550 is limited by the trans-
former used in the flyback converter circuit, a different isolated
power supply could be used in applications requiring full 3.75 kV
rms insulation voltage rating of the ADuM3165.
If even higher insulation ratings are required by the application, the
ADuM4165 or the ADuM4166 can be used as an alternative USB
digital isolator. Analogous to the ADuM3165 and ADuM3166, these
two devices share the same specifications and are pin-compatible
except for the placement of the XI and XO pins. The ADuM4165
and ADuM4166 feature a reinforced surge isolation voltage rating of
8 kVPK and a high dielectric insulation voltage rating of 5 kV rms,
but also have a larger footprint compared to the ADuM3165 and
ADuM3166.
Alternative power solutions, such as the ADuM6020 isolated
DC/DC converter, have an insulation voltage rating of 5 kV rms,
but is only capable of supplying a maximum current of 100 mA.
The CN0419 circuit note is a smaller, lower power USB digital isola-
tor reference design for applications that do not require high-speed
USB 2.0.



Html Pages

1 2 3 4 5


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com