STLC5048 datasheet(12/45 Pages) STMICROELECTRONICS

12 / 45 page

STLC5048

12/45

SLIC CONTROL INTERFACE

The device provides 12 I/O pins plus 4 CS signals. The interface can work in dynamic or static mode: it can be

selected by means of STA bit of the CONF register.

Dynamic Mode: the I/O pins are configured as input or output by means of DIR register. The CS signals

are used to select the different SLIC interface. In this case the I/O pin can be multiplexed. The data

loaded from SLIC #n via I/O pins configured as input can be read in the DATAn register. The data written

in a DATAn register will be loaded on the I/O pins configured as output when the Csn signal will be

active.

Static Mode: The CS signal can be used as I/O pins. They can be configured as input or output I/O by

means of DATA1 register. The data corresponding to the CS signal can be read or written by means of

DATA2 register. All data related to the other I/O pins can be read or written by means of DATA0 register.

DC SLIC PROGRAMMABILITY

Three additional pins are used to select the On-Hook/Off-Hook detection threshold and the line card limitation

of the STLC3080 SLIC. This two values are programmed by ILIM and ITH registers. The programmation of

these two registers must be done before the filter coefficients download.

The VBG input pin must be connected to the IREF pin of the STLC3080.

When the L3235N is used in kit with STLC5048 the ILIM, ITH and VBG pin must be not connected.

BUILT IN TEST

By means of TONEG register it is possible to inject a tone of variable frequency (25Hz, 1 and 3KHz) and 0dBm0

amplitude into the receive path, replacing any signal coming from the PCM interface. This test can be performed

on every channel.

Setting the proper bit of the PCMCOM register is also possible to read/write the PCM data coming from the

transmit path via the MCU interface (PCMRD/PCMWD registers). This feature can be enabled only on one

channel per time.

These two features can be used to test the line interface operation.

Addr

Name

Description

00h

DIR-L

I/O Direction (bit 7-0)

01h

DIR-H

I/O Direction (bit 11-8)

02h

DATA0-L

I/O Data ch#0 (bit 7-0)

03h

DATA0-H

I/O Data ch #0 (bit 11-8)

04h

DATA1-L

I/O Data ch#1 (bit 7-0)

05h

DATA1-H

I/O Data ch #1 (bit 11-8)

06h

DATA2-L

I/O Data ch#2 (bit 7-0)

07h

DATA2-H

I/O Data ch #2 (bit 11-8)

08h

DATA3-L

I/O Data ch#3 (bit 7-0)

09h

DATA3-H

I/O Data ch #3 (bit 11-8)

0Ah

PCHK-A

Persistency Check Time for input A

0Bh

PCHK-B

Persistency Check Time for input B

10h

INT

Interrupt register

STLC5048 Datasheet(PDF) 12 Page - STMicroelectronics

STLC5048 Datasheet(HTML) 12 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45

Datasheet Download

Link URL