TLV1544C, TLV1544I, TLV1548C, TLV1548I, TLV1548M

LOW-VOLTAGE 10-BIT ANALOG-TO-DIGITAL CONVERTERS

WITH SERIAL CONTROL AND 4/8 ANALOG INPUTS

SLAS139C – DECEMBER 1996 – REVISED JANUARY 1999

16

POST OFFICE BOX 655303

operating characteristics over recommended operating free-air temperature range,

PARAMETER

TEST

CONDITIONS

MIN

TYP†

MAX

UNIT

EL

Linearity error (see Note 6)

±0.5

±1

LSB

ED

Differential linearity error

See Note 2

±0.5

±1

LSB

EO

Offset error (see Note 7)

See Note 2

±1.5

LSB

EG

Gain error (see Note 7)

See Note 2

±1

LSB

ET

Total unadjusted error (see Note 8)

±1.75

LSB

DATA IN = 1011

512

Self-test output code (see Table 3 and Note 9)

DATA IN - 1100

0

DATA IN = 1101

1023

t

Conversion time

Fast conversion speed

See Figures 15

7

10

µs

tconv

Conversion time

Slow conversion speed

g

through 17

15

25

µs

t

Total cycle time (access,

sample conversion and EOC

↑

Fast conversion speed

See Figures 15

through 18 and

Notes 10, 11, 12

10.1 +

10 I/O CLK

µs

tc

sample, conversion and EOC

↑

to CS

↓ delay)

Slow conversion speed

See Figures 15

through 18 and

Notes 10 and 12

40.1 +

10 I/O CLK

µs

tacq

Channel acquisition time (sample)

See Figures 15

through 18 and

Note 10

6

I/O CLK

periods

tv

Valid time, DATA OUT remains valid after I/O CLK

↓

See Figure 11

50

ns

td1(FS)

Delay time, I/O CLK high to FS high

See Figure 13

5

30

50

ns

td2(FS)

Delay time, I/O CLK high to FS low

See Figure 13

10

30

60

ns

td(EOC

↑ – CS↓) Delay time, EOC↑ to CS low

See Figure 14

and Note 5

100

ns

td(CS

↓ – FS↑)

Delay time, CS

↓ to FS↑

See Figures 17

and 18

1

7

I/O CLK

periods

td(I/O -CS)

Delay time, 10th I/O CLK low to CS low to abort

conversion (see Note 13)

See Figure 10

1.1

µs

† All typical values are at TA = 25°C.

NOTES:

2. Analog input voltages greater than that applied to REF + convert as all ones (111111111111), while input voltages less than that

applied to REF – convert as all zeros (000000000000). The device is functional with reference down to 1 V (Vref+ – Vref – 1); however,

the electrical specifications are no longer applicable.

5. For all operating modes.

6. Linearity error is the maximum deviation from the best straight line through the A/D transfer characteristics.

7. Zero error is the difference between 0000000000 and the converted output for zero input voltage. Full-scale error is the difference

between 1111111111 and the converted output for full-scale input voltage.

8. Total unadjusted error comprises linearity, zero-scale, and full-scale errors.

9. Both the input data and the output codes are expressed in positive logic.

10. I/O CLK period = 1 /(I/O CLK frequency) (see Figure 8).

11. For 3.3 V to 5.5 V only

12. For microprocessor mode

13. Any transitions of CS are recognized as valid only when the level is maintained for a setup time after the transition.