LT1013AMH datasheet(5/24 Pages) LINER

5 / 24 page

LT1013/LT1014

10134fc

The

● denotes the specifications which apply over the temperature range

–40

°C ≤ TA ≤ 85°C for LT1013I, LT1014I, 0°C ≤ TA ≤ 70°C for LT1013C, LT1013D, LT1014C, LT1014D. VS = ±15V, VCM = 0V unless

otherwise noted.

LT1013C/D/I

LT1013AC

LT1014AC

LT1014C/D/I

SYMBOL PARAMETER

CONDITIONS

MIN

TYP

MAX

MIN

TYP

MAX

MIN

TYP

MAX UNITS

VOS

Input Offset Voltage

●

—

240

—

270

—

400

μV

LT1013D/I, LT1014D/I

●

—

230

1000

μV

VS = +5V, 0V; VO = 1.4V

●

—

350

—

380

—

110

570

μV

LT1013D/I, LT1014D/I

VS = +5V, 0V; VO = 1.4V

●

—

280

1200

μV

Average Input Offset

(Note 3)

●

—

0.3

2.0

—

0.3

2.0

—

0.4

2.5

μV/°C

Voltage Drift

LT1013D/I, LT1014D/I

●

———

—

0.7

5.0

μV/°C

IOS

Input Offset Current

●

—

0.2

1.5

—

0.2

1.7

—

0.3

2.8

VS = +5V, 0V; VO = 1.4V

●

—

0.4

3.5

—

0.4

4.0

—

0.5

6.0

Input Bias Current

●

—

VS = +5V, 0V; VO = 1.4V

●

—

AVOL

Large Signal Voltage Gain

VO = ±10V, RL = 2k

● 1.0

5.0

—

1.0

5.0

—

0.7

4.0

—

μV

CMRR

Common Mode Rejection

VCM = +13.0V, – 15.0V

●

116

—

116

—

113

—

Ratio

PSRR

Power Supply Rejection

VS = ±2V to ±18V

● 101

119

—

101

119

—

116

—

Ratio

VOUT

Output Voltage Swing

RL = 2k

● ±12.5 ±13.9

—

±12.5 ±13.9 — ±12.0 ±13.9 —

VS = +5V, 0V; RL = 600Ω

Output Low

●

—

613

—

613

—

613

Output High

● 3.3

3.9

—

3.3

3.9

—

3.2

3.9

—

Supply Current per Amplifier

●

—

0.36

0.55

—

0.36

0.55

—

0.37

0.60

VS = +5V, 0V; VO = 1.4V

●

—

0.32

0.50

—

0.32

0.50

—

0.34

0.55

ELECTRICAL CHARACTERISTICS

Note 1: Stresses beyond those listed under Absolute Maximum Ratings

may cause permanent damage to the device. Exposure to any Absolute

Rating condition for extended periods may affect device reliability

and lifetime.

Note 2: This parameter is guaranteed by design and is not tested. Typical

parameters are defined as the 60% yield of parameter distributions of

individual amplifiers; i.e., out of 100 LT1014s (or 100 LT1013s) typically

240 op amps (or 120 ) will be better than the indicated specification.

Note 3: This parameter is not 100% tested.

LT1013AMH Datasheet(PDF) 5 Page - Linear Technology

LT1013AMH Datasheet(HTML) 5 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Datasheet Download

Link URL