Key Features:

A1100RW

Miniature, 10W DIP

Miniature, 10W DIP

Single & Dual Output

Single & Dual Output

DC/DC Converters

DC/DC Converters

Series

Input

Parameter

Conditions

Min.

Typ.

Max.

Units

Input Start Voltage

12 VDC Input

7.0

8.0

9.0

VDC

24 VDC Input

14.0

16.0

18.0

48 VDC Input

30.0

33.0

36.0

Input Filter

π (Pi) Filter (Complies with EN55022 Class “A”)

Reverse Polarity Input Current

0.5

A

Short Circuit Input Power

2,500

mW

Output

Parameter

Conditions

Min.

Typ.

Max.

Units

Output Voltage Accuracy

±0.6

±1.2

%

Output Voltage Balance

Dual Output , Balanced Loads

±0.5

±1.0

%

Line Regulation

Vin = Min to Max

±0.3

±1.0

%

Load Regulation, 2.5 Vout Models

Iout = 10% to 100%

±0.7

±1.5

%

Load Regulation, All Other Models

Iout = 10% to 100%

±0.5

±1.2

%

Ripple & Noise (20 MHz) (Note 1)

50

85

mV P - P

Ripple & Noise (20 MHz)

Over Line, Load & Temp.

100

mV P - P

Ripple & Noise (20 MHz)

15

mV rms

Output Power Protection

110

150

180

%

Transient Recovery Time (Note 2)

25% Load Step Change

250

500

µSec

Transient Response Deviation

±3.0

±5.0

%

Temperature Coefficient

±0.01

±0.02

Output Short Circuit

Continuous (Autorecovery)

General

Parameter

Conditions

Min.

Typ.

Max.

Units

Isolation Voltage

60 Seconds

1,500

VDC

Isolation Voltage Test

Flash Tested for 1 Second

1,650

VDC

Isolation Resistance

500 VDC

1,000

MΩ

Isolation Capacitance

100 kHz, 1V

1,000

1,200

pF

Switching Frequency

400

kHz

Environmental

Parameter

Conditions

Min.

Typ.

Max.

Units

Operating Temperature Range

Ambient

-40

+25

+60

º

C

Operating Temperature Range

Case

-40

+90

º

C

Storage Temperature Range

-40

+125

º

C

Cooling

Free Air Convection

Humidity

RH, Non-condensing

95

%

Conducted EMI

EN55022 Class “A”

Physical

Case Size

1.25 x 0.80 x 0.40 Inches (31.8 x 20.3 x 10.2 mm)

Case Material

Metal with Non-Conductive Base

Weight

0.61 Oz (17.3g)

Reliability Specifications

Parameter

Conditions

Min.

Typ.

Max.

Units

MTBF

1.0

MHours

Absolute Maximum Ratings

Parameter

Conditions

Min.

Typ.

Max.

Units

Input Voltage Surge (1 Sec)

12 VDC Input

-0.7

25.0

VDC

24 VDC Input

-0.7

50.0

48 VDC Input

-0.7

100.0

Lead Temperature

1.5 mm From Case For 10 Sec

260

º

C

Internal Power Dissipation

All Models

2,500

mW

Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.

MicroPower Direct

292 Page Street

Suite D

Stoughton, MA 02072

USA

T: (781) 344-8226

F: (781) 344-8481

E: sales@micropowerdirect.com

W: www.micropowerdirect.com

RoHS Compliant

Electrical Specifications

Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.